MDB100RGW1 Uni Dishwasher - Instructions

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. ... Read more The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

I just popped on a new Arm. So easy. The amazing thing was how fast I had the part and how easy it was to find on Partselect.com. I ordered the part Monday and had it Tuesday. I was stunned and the tenant was impressed.

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

First I shut off the power to the dishwasher from the breaker panel. Then I removed the five screws holding the plastic top panel to the door (on the frigidaire, there is no need to remove the entire stainless steel door panel). I removed each of the four wires from the old latch (pulling the wires off required some "oomph") one by one ... Read more and plugged them into the corresponding position on the new one. I did this so I would be sure to have them in the right place. I used a torx screwdriver to remove the two screws holding the old latch. I then replaced the old latch with the new one, replaced the top panel of the door, turned the breaker back on and everything was as good as new! The whole operation took maybe 20 minutes. It couldn't have been easier. The only surprises were how difficult it was to pull the wires off and the fact that the screws holding the latch were torx head.

In future, when I need parts, I will definitely use PartSelect. I have gotten parts from other sources, and this is the first place where, along with the part, you get all this advice from other DIY'ers. It's an absolutely brilliant idea and a lot of help.

remove vanity panel
disconnect copper supply line from valve
remove valve mounting screws
rotate valve to access hose clamp
loosen clamp and slide up rubber tubing about 2 inches
pull hose off barbed fitting and remove old valve
reverse order with new valve

took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it w ... Read more ith silicone caulk, but may have to replace that - looks easy, .

Took the dishwasher out removed the two screws and the part holding the motor in and removed the motor. Received the parts, places o'rings on the motor, which came with the kit, even though I ordered the two o'rings. Replaced the motor, installed the part that holds the motor and tightened the screws. Cut the old connector off the di ... Read more shwasher and replaced it with a new connector that came with the kit. Reinstalled the dishwasher, works great. Thanks for your Site.

Removed screws and put new bottom gasket in old one just fell out.

Snapped the new one on

Found your website, red the reviews, followed the simple instructions provided by others that had had the same problem and repair was complete in less than a minute. No tools needed. I am a handy girl and tackle a lot of repairs/projects, this is the first time that the job was actually easier than stated. Thanks for providing a good p ... Read more orduct, at a decent price WITH LAYMAN INSTRUCTIONS!!!

pulled the old part off (no tools required) and snappen on new spray arm

PartSelect provided the perfect place to order the parts I needed. Illustrated parts breakdown on PartSelect was excellent and the correct part(s) were identified and ordered with no difficulty. I would recommend PartSelect to anyone.

Remove old spray arm and pressed the new part into place. Let the dishwasher run and the load came out very clean. Overall very pleased.

I disconnected the power to the machine. Removed the bottom access panel and screws holding the dishwaher in the cabinet opening so I could carefully slide the dishwasher out.
Taking note of the pump position at the bottom of the dishwasher I removed the two wire leads, screws and hoses(pliers). I installed the new part in the rever ... Read more se order and was able to run the dishwasher for a cycle while it was out to make sure there were no leaks.
Dishwasher runs great and the dishes seem cleaner. Fingers crossed.
Thanks.