MAH4000AWW Maytag Washer - Instructions

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

It was easy as 1,2,3. Took the old knob apart and replaced it with new one. About 20 minutes.

Very easy.I used a screw driver to remove and install the new hinges. Three screws on each hinge. Door closes like new again.

Disconnect power. Remove back panel. Use shop vac to remove water from drum. You can also remove one of the agitator fins from the drum (uses 2 TORX screws) to gain access to inner tub drain hole to remove additional water with shop vac and check for obstructions. Remove power wires from pump, noting position of each. Place towel near pum ... Read more p and disconnect input and output hoses. Rotate pump to disengage from slots in base, and remove. Installation is reverse.

The first step to repairing this problem is to remove the hoses and back panel of the washer. Next detach both the hoses attached to the pump ( have some towels handy because their will be a lot of water pouring out of the pump). Before removing any screws on the pump, use a wrench to remove the bottom platform securing the pump inside of ... Read more the washer. On the the Amana washer there should be about three bolts holding this small platform down. After unscrewing the bolts, unsnap the wire connected to the motor and remove the platform to get the entire pump out of the washer. The next step is to unscrew the screws on the bottom of the platform to release the base of the pump. The next step is to put the new pump on that same platform. FYI the new pump may not fit on the platform. To solve this problem, unscrew the motor/pump(the black thing) from the base holding the motor( the cream or white colored part). Do this step for the old and new motor/pump. Screw your new motor to the old base. Screw the base with the motor attached back on the platform. Connect the wire in the washer back to the motor. Screw the platform back in the washer and reconnect everything that was disconnected to remove the motor/pump. Finally put the back panel back on the washer and run a test cycle. The washer should now be able to drain.

Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!

removed door,Opened the front panel, opened the top and proped it out of the way. Pulled the boot from the front cover disconnected the drain, released the boot clamp and pulled the boot off. I cleaned the inside of washer and soap tray. cleaned debris from the drain hose. repaired a broken soap dish connection. changed supply hoses and n ... Read more ew valves. Generally checked cleaned and overhauled the washer.

Basic disassembly as described earlier.Some tips I found helpfull. Use vice grip pliers on spring.it will keep a grip on the spring hook and you can exert more force to pull the spring.Th bellows was very sticky and hard to slip into place. I put a litle silicone lube ( stuff you use for pool pump gaskets )on the bellows. It made it slip ... Read more into place easly.

Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.

Bought the parts and just inserted them.

Removed existing screws along with damaged bezel and replaced with same screws.

I removed 4 screws and removed the bezel, moved the access door to the new bezel and secured the new one with the 4 screws, all done and wife is very pleased.

I removed the old Dispenser Bezel and replaced it with the new part.

Wow! Thanks to the customer info/hints already posted the repair went super smooth and was relatively easy to accomplish. $70.00 for an easily replaced part sure beats $1,000+ for a new washer. Super fast shipping reduced down-time significantly!!! From start to finish the job took less than 30 minutes. Thank you so much.

Tilt washer onto door with back of washer on top for easier access.