MAH3000AKW Maytag Washer - Instructions

First I removed the 4 screws that kept the bezel in place, removed the bezel. Replaced the new bezel, replaced screws, put new top pin in door and put door on.

We followed the directions in other people's repair stories here. Removing the spring was a challenge, as was getting it back on! The rest of the repair was simple. Be patient with removing the soap dispenser. Ours had some plastic cords connecting it to the frame which we didn't anticipate, and we broke them because we didn't see them.

We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.

The repair was only 4 screws.

THE AMAZING STORY WAS I ORDERED THIS PART ON MONDAY AND RECEIVED IT ON WEDNESDAY!!!!!!

There was 4 screws that held the bevel in that still needed to be removed from the old broken one. Once we removed those we were able to place the new bevel and lid in the correct sport, replace the screws and viola, perfect.

Even though after reading many repair blogs saying not to remove the back of the washer, I did anyway. Lo and behold after opening it, the pump was right there!! I removed the hoses (make sure you have a bucket, or shop vac handy) lots of water will come pouring out use your bucket for this, I used my shopvac to suck the rest of the water out of the hose, and bing, the washing maching door opened and allowed my to retrieve my clothing(stinky now after the washing machine held them hostage for days) I removed it by removing 3 bolts, and 1 screw very easy. I took apart the pump to see if there was anything blocking up the moter there was nothing, but the plastic pump blade was chewed up so bad, it no longer would turn to pump out the water. I had to order a pump. When my pump came in 2 short days later, I reversed to removal process and presto!! The washing machine was running like new.

I removed the back panel and located on the left side of the washer removed the pump and replaced it.

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Removed back of washer and unscrewed pump band and hose removed pump and replaced pump,replaced hose to new pump,WE really appreciated the fast shipping of the part from your facility.Thank You again

Unscrew door hinges, front panel, soap tray, lift top to 12 oclock position,unhook strap from spring located on top of the drum,tape strap ends to drum to prevent from falling,disconnect the billows drain clamp on the bottom of the billows,remove the billows by peeling off the drum, install the new billows from the top first and tape it to the drum to prevent it from slipping off as you work your way around the drum,install the strap in its track, secure with spring(better with two people)in same location, hook up billow drain, finish doing the laundry.

Received 2 seals with seal kit and didn't know which seal went where and online it was stated in a video the kit included a "revised" seal but couldn't find anymore information than that. Installed what I thought was the seal to be installed on the inner seal. Did not have any information on the depth of the bearings installation on outer or inner bearing set depth. Tried to call help line but never got through. I think it is installed right? Guess I will wait and see how the drum holds up and hope the bearings and seal are installed correctly.

The motor isolators went in with no problem ,but the drive belt went on very tight , your how to video shows how. Easy the belt went on , when I called your store I was told that is the only size belt for the machine model mah5500bww,
Thank you Bill

Beat on spline shaft until I gave up and trashed the washer. Bought new washer.

Replace front legs. Very easy fix.

Everything went smoothly enough until I reached the tension spring issue...It is definitely a two person job (that part, al least) It may be helpful to add that to the video...otherwise, the repair went well as I followed the video completely

removed phillips headed screws from sides (hinge on one side) and bottome of door, placed door flat on counter top. Removed interior vent, disassembled the door latching mechanism - somewhat difficult to figure out because needed to undo snapped in parts (used flat screwdriver to pry). Then removed inner panel from door, placed new inner panel into door interior, reassembled door latch mechaninsm, replaced vent tube. screwed in phillips head screws to bottom and non-hinged side of door. Brought door back over to machine and attached hinges to door.