LWA50AW (PLWA50AW) Amana Washer - Instructions

Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!

I first ordered the parts and to my dismay, I ordered the wrong belt for the spin belt. I called customer service in which received an Return Merchandise Number and ordered the correct belt. PartSelect was prompt on sending the correct out by FedEx, thank you for an excellent experience.

First I removed the 5 screws holding the control panel in place then tilted panel forward to gain access to the mounting screws to the timer and the electrical connection and removed and replaced the timer. Worked great the first time.

Laid washer on its side and had to remove the motor,replaced the pulley and belt replaced the motor and put all parts back together washer spins and runs like it did when it was new.we did not need the screw or nut but did not know when ordering parts

Remove the front of the washer. Remove the pump and motor assembly using the 1/2 inch socket. Remove the pump from the motor and hoses from the pump. Replace the bad idler pulley and place new belt on pulley. Reassemble the pump to the motor and install the assembly back into the washing machine. Reasemble the hoses and put belt on driven pulley for the drum. Reinstall the front cover.

I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

checked for unbalanced load. still banging. removed lower front panel by removing 2 screws. then removed front top panel- 2 more screws. turned unit on spin cycle to see what was going on. this is dangerous as many moving parts are exposed, so keep everything clear. banging was the tensioner slamming back and forth. unpluged washer from outlet and felt along the belt to find part of the 'v' shaped balt had come part, leaving a gap in the "v". ordered part.when i got the part, i removed 4 larger bolts that held the motor, pully, and pump. i unplugged the wires for the motor, and removed the belt from the bsket side pulley assembly by slipping it off and under the shaft. i removed the torx screws that held the pump on the motor and removed the belt. PAY ATTENTION to how the belt was in between the pully and pump assembly or you will have to remove and redo it. reassemble the pump over the belt, pully, motor, and put the belt on the drum side pully before bolting it to the washing machine. it is fairly heavy and tight, so you might need help. this was not hard and you do not need to take apart the washer except for the two front panels and the motor assembly. i just pulled the unit away from the wall and tipped it back to access the inside. take your time and pay attention, and make sure it is not plugged into the wall and you should be fine.

Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

Followed video on PartsSelect website, they made it real easy.

Removed and replaced mixing valve. Shut off hot & cold water supply to machine. Pull machine electric plug. Access back of machine. Remove water supply to machine. (Pliers) Be sure to keep some paper towels handy to pick up residual water. Remove screw that holds mixing valve mounting plate to machine. Pull plate away from machine. Undo hot and cold elect. connectors to valve. Remove water supply to valve. (Black hose-screwdriver.) Remove screw holding valve to mount plate. (Nut driver.) Install new valve onto mount plate. Reverse process used to remove valve. Test by turning on machine.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

Water inlet valve was different than the one shown on web photo. The hose supplied was the wrong size so I had to use the original old hose. Wire harness had to be modified since the electrodes were on opposite sides of the valve. Overall I was disappointed with the part and the service.

I used my three jaw slide hammer to remove the pump from the motor. How are other people getting it off? Pump made alot of rubbing noise after installation. I tried pushing it on farther and also prying it back off a little with no luck. It's really cheap looking and I was scared of breaking it. The thing wasn't leaking so I called it good....