- Home
- LRSC21935SW
- Instructions
LRSC21935SW LG Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
bad switch
1 person
found this instruction helpful.
-
Michael from TONAWANDA, NY
- Easy
- 15 - 30 mins
-
Screw drivers
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this helpful?
Thank you for voting!
The switch became intermittent - Possibly a poor designe
1 person
found this instruction helpful.
-
Sidney from ENDICOTT, NY
- Very Easy
- Less than 15 mins
-
Screw drivers
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this helpful?
Thank you for voting!
door slight switch failed
1 person
found this instruction helpful.
-
Greg from CASA GRANDE, AZ
- Really Easy
- Less than 15 mins
-
Pliers
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this helpful?
Thank you for voting!
Door light switch, 3rd one I have replaced in 6 years made in China.
1 person
found this instruction helpful.
-
Charles from CURWENSVILLE, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this helpful?
Thank you for voting!
Replace switch
1 person
found this instruction helpful.
-
Dean from HILLSDALE, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this helpful?
Thank you for voting!
the light did not work when door was opened. At first it would flicker then off completely.
1 of 2 people
found this instruction helpful.
-
Alma from Winterport, ME
- Very Easy
- Less than 15 mins
-
Screw drivers
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this helpful?
Thank you for voting!
Replace the light switch for the refrigerator
1 of 2 people
found this instruction helpful.
-
Karyn from DURHAM, NH
- Really Easy
- Less than 15 mins
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and
... Read more
careful push the switch into the hole until it snaps into place.
Read less
Was this helpful?
Thank you for voting!
Water and Ice dispensing just stopped working. Also Ice trap was broken.
1 of 2 people
found this instruction helpful.
-
BRENT from Glendale, AZ
- Easy
- 1- 2 hours
-
Screw drivers, Wrench (Adjustable)
Water valve replacement at back bottom right. Removed, water supply line and old valve with 1 screw and removed clips from hoses. Replaced with new valve and re-clipped hoses. Easy fix! Cleaned coils and back with blower and vacuum cleaner while I was in there too. I also had leak in water supply line, replaced. Ice trap door replacement
... Read more
was a little more challenging. Hard to get off the ice dispenser funnel (Part# 278D). Has 4 lock clips on it and 1 broke when I took it off. This part# 278D is not available from part select?? Tricky to replace the trap door itself. Have to make sure the door valve sits in solenoid correctly. Installed wrong the first time and door would not open/close. Had to go in and reset orrectly. Works like a charm now. Still need part# 278D!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator light had a short in it and would randomly work
1 of 3 people
found this instruction helpful.
-
Tammy from HAGERSTOWN, MD
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Was this helpful?
Thank you for voting!
Unit kept beeping as if the freezer door was open
0 of 1 people
found this instruction helpful.
-
Paul from San Jose, CA
- Really Easy
- Less than 15 mins
-
Pliers
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
Was this helpful?
Thank you for voting!
water supply to ice maker leaked
0 of 1 people
found this instruction helpful.
-
john from locust valley, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Was this helpful?
Thank you for voting!
light out
0 of 1 people
found this instruction helpful.
-
Jack from Ellenton, FL
- Easy
- Less than 15 mins
-
Screw drivers
slid screw driver under edge of switch, easy.
Was this helpful?
Thank you for voting!
The water line was leaking
0 of 1 people
found this instruction helpful.
-
Awilda from Staten Island, NY
- Easy
- 15 - 30 mins
-
Screw drivers
Removed the damaged tube and replaced the it with a new one.
Was this helpful?
Thank you for voting!
Water/ice maker not working
9 of 38 people
found this instruction helpful.
-
Brent from ROGERS, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Was this helpful?
Thank you for voting!
Ice cubes did not drop out of tray when the ice maker cycled
-
Michael from Eagle, WI
- Easy
- 15 - 30 mins
-
Screw drivers
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the t
... Read more
ray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!