LAT5006AGE Maytag Washer - Instructions

I opened up the control panel on the back by removing the 4 screws and then used the print that was inside to check where the power went from the power cord. I checked the power at diferent places and determined that I did not have power coming from the lid switch with the door up or down. You could here the switch click when you opened a ... Read more nd closed the door but aperantly it was not working. After going on your web site and looking at the other posts I realixed that there was a fuse link in the switch that was probably blown. I ordered the switch and it was a simple matter to replace when it arrived. The washer works great once more.

I did a continuity check on the lid switch assembly since it was a) the easist to get to, and b) my wife's descreiption of how rthe washer stopped made me think it had something to do with the lid switch.
I found that all of the contacts were open regardless of the position of the switch, and I also discovered that there was a fuse i ... Read more nside the swithch. I decided to order a replacement part based on the presence of the fuse.
Upon repacling the fuse (a snap in affair), the washer was working again... my wife was impressed and I was happy!

The instructions were clear. Did every step. Did 2 loads so far and everything works like new.

I followed Dan from Mason OHIO instructions.They were perfect. I have a different series washer so I did not need the washer and retaining ring. I used 2 lengths of 4x4 to support the tub when smacking the bearing with the narrow side of a 2x4 to drive it out. You hit it from the inside of the tub. When installing the new one, use the wid ... Read more e side of the 2x4 to drive it flush.

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and ... Read more added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece ... Read more on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck

Good.

First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixe ... Read more d to your machine where you can lift the lid and it will stay up without falling.

Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.

Tried the water level control first. didn't fix it.
Then replaced the air tube for tub fill volume.

The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it.
The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so ... Read more it changed the air volume.
That reduced air volume caused the air pressure to be wrong to the water level sensor.
My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.

Power cord out, of course.Popped off the front panel, swinging bottom outward. Wedge shaped protrusions on top of front panel work as a hinge until the bottom is swung out and the entire front lowered. Unscrewed the top--one screw in each front corner accessed from the front opening (removed panel). Panel behind control panel must be remo ... Read more ved (5 hex head screws). Tilted front of top up revealing broken injector. Retaining screw for injector accessible from behind control panel loosened and broken injector assembly removed. New (easily assembled--snap together) injector slid into holding slot on one side and screwed down with previously removed hex screw. Reassemble in reverse.

I removed three small bolts on the back of top panel unpluged electric plug on lid switch popped out old switch popped in new plugged in switch put top back on with the three small bolts. The wife was back in business. Easy as 1 2 3

unhooked power plug removed 2 top screws tilted topfront panel back removed cracked fuse holder replaced with new fuse holder put top cover back on installed 2 top screws plugged in power cord done!

Took off the top rear off the washer, Removed the top control section,disconnected the wire harness, snaped out the old switch and installed the new one, connected the wire harness, put everything back together, and it was working again!

Followed the procedures recommended for replacement of all the parts included in the Tub Bearing Kit and the Mounting Stem/Tub Seal kit as illustrated in a detailed, 32 minute repair video for the Maytag A606 washer which is available on YouTube. Many difficulties were experienced in the disassembly procedures due to extensive corrosion ... Read more of tub bearing and tub stem parts (the washer is 47 years old).
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.

Very Easy Repair! Removed 2 screws at the bottom using a philips screw driver(one on each side). Lifted the cover up to detach. 2 screws at the top were removed using a socket set (one on each side). Old tub cover snapped off easily. Make sure you set the cover the same way as the old cover. The new cover snapped on with minimal force. Ma ... Read more ke sure it's fully seated. Put everything back together in reverse. Took 20min. Most of the time searching for the tools.