KUDS30IXSS8 KitchenAid Dishwasher - Parts

This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to mak...Read moree sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.

This part has been redesigned and now comes in a kit. This kit includes 2 adjuster assemblies, 1 left-hand and 1 right-hand actuator cover, 2 gray adjuster covers, and 2 gray adjuster housings.

The door balance kit helps support the dishwasher door. This kit includes 2 door balance links and 2 door balance mounts with wheels.

This chopper assembly chops up/mince the food particles to prevent from clogging the dishwasher pump.

Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the dishrack. If your clip is cracked or damaged, it is best to replace this part. To repair, first lift the release tab and hold the other side...Read more to prevent it from falling off. After lifting it off, you can set the new clip on the tine row and lock it up. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to wear work gloves as a safety precaution. This repair was rated as very easy by our customers and should be done in 15 minutes or less.

This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and falling off. If broken or damaged, then the rack will slide too far and this is a sign the part should be replaced. It attaches to the end of t...Read morehe top dishwasher rack. This clip can be used for the left or right side, and is sold individually. It is a good idea to replace both sides at once. To make this repair, start by pulling out the rack, then, using your screwdriver, reach in behind the rack stops and press the clips in. You should be able to remove the stops from the track from here. Next, you should be able to slide the track back over the rollers and snap the new track stop into place.

This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips...Read more screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

Prevent leaks and maintain optimal cleaning performance with this durable dishwasher door seal. It creates a secure barrier to keep water contained during wash cycles, ensuring reliable operation. Replace by removing the old seal and fitting the new one snugly around the door frame.

This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The door seal is designed to seal the gap between the dishwasher tub and outer edge of the door. This helps to prevent leaks when your dishwashe...Read morer is running. A leaking dishwasher is a good indication that the door seal is damaged. This seal is sold individually and is an OEM part sourced directly from the manufacturer.

Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip holds the adjuster arm in the right position on the dishrack. The most common reason for replacing the strap is if the rack will not stay i...Read moren its desired position. This part is sold individually. There are no tools needed to replace the positioner.

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.