KSDG950ESS1 KitchenAid Range - Instructions

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), ... Read more which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Remove the range door. Look on YouTube. Remove 4 screws holding on the fan cover at the rear wall of the range. (This was a slide in range and I could not get to the back without a lot of extra work.) Remove the 3 screws holding the fan in place. Be care and handle the fan gently. Remove the fan by moving outward slightly. Be very ... Read more careful of the electrical connections on the back of the fan. There are 4. Tilt the assembly out from the top a couple of inches. Slide off the two wires to the heating element, lower the assembly down while keeping the bottom close to the range back wall. Slide off the two connection fan wires on the bottom. Be careful and do not over stress this plastic harness wire connection, it will break. Remove fan. Put the new one on. First slide on the harness connection at the bottom while holding the bottom of the fan close to the range back wall. Rotate up and hook the two element wires. Put the screws back in for the fan and cover. This is very sensitive work. Take you time.

I have tried to call, but NO-ONE answers the phone. I have sent emails, but all I get is an automated response telling me to go to the web site. Partselect is the worst company I have ever dealt with, I need to return about $100 in parts and I cannot get an automated return form or someone on the phone. I will NEVER do business with ... Read more them or recommend them to anyone. In a nutshell they SUCK as a company.

Toke the oven door off disassembly door and replaced outer panel and glass

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

very expensive to buy the part but just tighten the screw intot eh predefined place.

There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.

Watched the video and realized this was something I could do myself...bear in mind I'm not exactly a handyman! Took me about 30min as the oven also needed some cleaning...my tenant definitely needs to use the self-cleaning!

I have to note, although the heating element was covered by Maytag's 10yr limited parts warranty, I deci ... Read more ded to purchase from PartSelect since Maytag could not provide a ship date and I couldn't keep my tenant waiting! Supposedly Maytag had the part in stock but their warehouse was behind because of the pandemic...what a lame excuse! Almost a month later, Maytag has yet to ship the part! Needless to say, am very disappointed in Maytag's after sales and warranty program! I get the impression, they just wanted to pressure me to buy the new part!

Lastly, was very pleased and impressed by PartSelect's customer service! Their website was very easy to use, less expensive than buying direct from Maytag and the part was shipped same day! Thank you PartSelect!

I watched then followed the video. I could not remove the top, so I used a can from the cabinet to support and hold the top. That gave me enough room to get the old fan out and the new fan in. Thank you PartsSelect.

ordered new broiler pan

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. ... Read more Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

The instructions given on this website were more than adequate, even though the element had been updated and now has only 1 point to screw down

screwed it in the oven and it worked.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.