Models > KEMS309BSS01 > Instructions

KEMS309BSS01 KitchenAid Microwave - Instructions

All Instructions for the KEMS309BSS01
31 - 45 of 66
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water spilled in oven shorted out the sensor-code 3D21 I think
Didn't need sensor replaced. After turning the breaker switch back on oven appeared to be working fine.
Parts Used:
Oven Sensor
  • JULIE from SPOKANE VLY, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bulb entirely to small and unopened
Should be about 1 5/8 inch with 3/8 inch prongs. Sent bulb won’t fit.
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I return the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961
Parts Used:
Halogen Light Bulb
  • Carolyn from BURLESON, TX
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven had error messages
I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.
Parts Used:
Oven Sensor
  • dan from Gallatin, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench set
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken glass tray
Just put it in
Parts Used:
Microwave Turntable Tray
  • Robert from HEMET, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Open the carton and install turntabe glass tray.
Fool proof.
Parts Used:
Microwave Turntable Tray
  • Roger from LYMAN, ME
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old microwave glass tray shattered while warming a hard-boiled egg.
I took the new tray out of the box and placed it in the microwave oven.. No tools needed.
Parts Used:
Microwave Turntable Tray
  • Raymond from HINSDALE, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Micro Wave Steamer
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
Parts Used:
Microwave Steamer
  • James from MIAMI, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part broken
We ordered element support 3 times and all three times it came broken. The part is made of porcelain and is fragile , representative asked warehouse to pack it in the box and part still came in envelope.
Requested refund and ordered directly from factory.
Parts Used:
GRILL SUPPORT
  • Elena from HOUSTON, TX
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part worn out
Could not complete the repair due to broken part when arrived. Reached out to service department but have not heard back. Maybe email did not go through due to pictures attached of part condition once arrived.
Parts Used:
COVER-PLT
  • Kerry from Carrollton, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Temperature not holding and blower squeeling
Put cribbing on a dolly, slid the oven out of the cabinet. Unfastened the upper broiler element allowing removing temperature sensor screw. Removed all the back panels and pushed the temperature sensor wire clip thru to the oven, Pushed the new emperature sensor wiring back thru the hole to the back. Removed and repalaced the blower re connected the wire harnes for the blower and temperature sensor.. Replaced all the back panels and slid the oven back into the cabinet. Re attached the temperature swensor and re fastioned the upper broiler element. All went well and am glad the sales lady sent the how to videos. The videos were foir a different model but were essentially the same.
Parts Used:
BLOWER Oven Sensor
  • Tom from BELLEVUE, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven temperature running higher than setting
This was easy to replace. I removed the oven door for easier access to the back of the oven. Removed two Phillips head screws that hold the burner element and disconnected the two wires on the burner element. I could have left the wires connected, but it was easier to extract the sensor with it out of the way. The only difficulty was fishing the sensor connector out through the hole. After that, easy peezy.
Parts Used:
Oven Sensor
  • Chris from LAGO VISTA, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inner glass door on oven was broken
Simply unscrew four small screws on the top aluminum cover plate ((two on top and two on the side of the plate) and the glass easily slides out and is replaced with the new glass. Once the glass is replaced, you simply screw the cover plate back on.
Parts Used:
Inner door liner & glass assembly
  • Alan from DENVER, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke the glass cooking tray when instaling my oven microwave combo
I put the tray in the microwave???? Pretty easy.
Parts Used:
Microwave Turntable Tray
  • Jeff from Baytown, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
INTERIOR OVEN LIGHT
EASILY REMOVED GLASS COVER INSIDE OVEN AND REMOVED SMALL HALOGEN LIGHT BULB.
RECEIVED REPLACED WITHIN TWO DAYS OF ORDER AND REPLACED BULB AND GLASS COVER IN ABOUT 10 MINUTES.
MOST DIFFICULTY WAS HAVING TO BEND DOWN TO REACH INSIDE OF OVEN TO LOCATE POSITION TO INSERT BULB.
Parts Used:
Halogen Light Bulb
  • Gary from WALTON, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken mounting bracket for coils in convection microwave.
Very easy, fit perfectly.No tools required.
Parts Used:
GRILL SUPPORT
  • Larry from Fernandina Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KEMS309BSS01
31 - 45 of 66
Back to Top