JVM1542BF03 - Instructions

Removed screws holding outer shell. Pushed in door handle to identify faulty switch. Ordered part. Pryed switch out with screw driver and unplugged. reinstalled new switch. Presto. BUT... I did NOT use both hands while working on the microwave. I did not release the energy from the capacitor or whatever holds the killer amperage even when unplugged. It would be advisable to do this first. I did not because it seemed complicated, so I was EXTREMELY CAREFUL about not touching anything else inside the unit. I used one hand only so if I did touch something I would not get juiced through the chest. It was a piece of cake repair, but I would not go deeper without doing the discharge routine.

I wasn't sure which parts I needed.We searched several web sites until we found yours.I was real pleased with the service. My parts where delivered in a timely manner. Everything I needed to install my microwave was in my order. Thank you for the service.
Georgia westchester ohio

just slipped the filter in place.

I removed four screws from the top, slid the front panal off, and slid the filter in then replaced the panal. The price I paid at PartSlect was half the price of any other place I tried, and that includes the shipping. The part was here in two days. Good job people, Bazzle Weiss

Had to remove outer cover (special screws involved). Found the correct part at PartSelect.Com and it arrived 3 days later as promissed.

This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver.

One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.

Removing interconnect switch is tricky but not difficult.

Outer cover replacement is not as easy as it should be, especially the sides.

All is well and working.

Microwaves are simple devices if you are know how to read and understand schemetic diagrams.

Replaced

new glass tray

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Watched a couple of repair videos on Youtube by searching for the model number. Found out what to do in order not to get shocked by the powerful capacitor.
Ordered the two switches (To be sure, I could have ordered a third switch as suggested in the videos.)
Bought a tamper-proof star bit to get the cover off. Followed the directions to replace the switches. - I broke the harness and had to use some super glue, but it's all good. I should have removed the harness instead of trying to get a switch out while it was still in place.
It's all back together, and the wife is happy!!

Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.

First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!

Just pulled off the cover, removed the old latch, re-connected the spring...put it all back togeather. Everything just snapps back in. The entire repair took about two minutes. Very easy.

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

Moved the stove from underneath the microwave. Took the microwave down and turned it over. this need not be done. took the screws out to remove the bottom panel. there is a quick disconnect that need to be opened up. used pliers to remove the bad sockets and installed new one, used pliers to seat them. put bottom panel on, hooked up the quick connect. put the screws in and tightened them. installed bulbs and hooked up the electric and turned the lights on, they worked. installed the microwave, slid the stove back in place.

The repair went well. It was really easy to replace the filters. We bought this house recently only to find out the previous owners threw all the filters for the microwave out including the two reusable grease filters. The grease filters were easy, just slipped them in. The charcoal filter required taking the top plastic vent off by removing two screws and slipping the filter in.