Models > JVM1490B > Instructions

JVM1490B - Instructions

All Instructions for the JVM1490B
91 - 105 of 219
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light bulb went out and I was unable to find the right size locally.
Had to use a screw driver to remove the cover to replace the bulb. Worked great and your service was great. Probably didn't take more than 5 minutes.
Parts Used:
Halogen Light Bulb - 120V 20W
  • Mary from Lawrenceville, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Glass Cooking Tray
Placed the new tray into the oven.
Parts Used:
Glass Cooking Tray
  • Gloria from ROSSFORD, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Door Latch on the Avantium Microwave Oven
I removed the door, by taking off the grill at the top. Then, take the puddy knife and screw driver and pry the facing off of the door. Please remember to be very careful because this is a sensitive piece. This is the most difficult part. It is a piece of cake after this. This should take about 15 minutes from beginning to end.
Parts Used:
Door Latch Assembly
  • Sherman from Memphis, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Just needed to replace the Wave Guide cover
Unscrewed the screw, removed old cover, place new cover in place and re-inserted the scrw.
Parts Used:
Wave Guide Cover
  • Henry from Roseland, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light bulb went out
Opened the light cover. Removed the old light bulb using a light tug on the old bulb, lined up the new bulb and pushed gently into the socket.
Turned the power back on and the microwave is good to go.
Parts Used:
Halogen Light Bulb - 10W 12V
  • Judith A from LAKEWOOD, CO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door latch broke.
It was really easy. I am not a handy person but I followed a video and got it done quite quickly. It saved me a lot of money. The local appliance repair service charges a minimum of $75 just for the visit plus parts.
Parts Used:
Door Latch Assembly
  • Michael from WANTAGH, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door latch broken
removed broken latch connected to existing spring done in less than two minutes works better than new
Parts Used:
Door Latch Assembly
  • Loretta from PRT JEFFERSON, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned wave guide cover
remove with phillips screwdriver. insert 3 corners in to slots and insert and tighten screw.
Parts Used:
Wave Guide Cover
  • Edward from ANTIOCH, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave would not heat up
Part just snapped into place and wires were reattached.
Parts Used:
Primary Door Interlock Switch
  • Suzanne from POWELL, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Switch went bad, Internal Fan would run every time you open the door
Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.
Parts Used:
Primary Door Interlock Switch
  • gilbert from TOMS RIVER, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
vent cover broke
two screws out two screws in done in seconds
Parts Used:
Vent Grille
  • robert from philadelphia, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
suddenly stopped working while in use
i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell
Parts Used:
Micro Switch
  • Kevin from Colonia, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb burned out
Remove 1 screw, remove light bulb and replace and replace screw. No problem.
Parts Used:
Halogen Light Bulb - 120V 20W
  • David from SAINT LOUIS, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Latch for door broken
Unplug power source.
Took off plastic panel partially on inside of door with door on its hinge.
Removed latch and spring.
Reinstalled new latch new spring (new part)
Reattached plastic panel to door.
Plug in power.
Parts Used:
Door Latch Assembly
  • Steven from TAMPA, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lawn mower would not start
removed cover over motor blew it out of leaves and dust. Removes 4 screws and removed piece ordered. The coil was rusted and not connecting. Changed oiece its working again
Parts Used:
Glass Cooking Tray
  • Lorraine from MIDDLETOWN, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JVM1490B
91 - 105 of 219