- Home
- JS630SF1SS
- Instructions
JS630SF1SS General Electric Wall Oven - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Plastic slide for storage drawer broken.
-
James from Stuart, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this helpful?
Thank you for voting!
Replaced damaged oven rack
-
Vicki from Irvine, CA
- Really Easy
- Less than 15 mins
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this helpful?
Thank you for voting!
Old dishwasher rack and silverware rack
-
Anne Marie from Andover, MA
- Really Easy
- Less than 15 mins
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this helpful?
Thank you for voting!
Range lower drawer would not stay on track.
-
Richard from Newark, DE
- Really Easy
- Less than 15 mins
-
Nutdriver
Easy to install replacement parts using the screws provided.
Was this helpful?
Thank you for voting!
Broken drawer support
-
Mario from Deer Park, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this helpful?
Thank you for voting!
rear drawer supports broke
-
TERRY from RICHMOND, VA
- Really Easy
- 15 - 30 mins
-
Socket set
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Was this helpful?
Thank you for voting!
The middle of the element quit working.
-
Ruth Ann from New Columbia, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Took the old burner out, tranferred the wires from old to new. Installed the new burner. Works fine.
Was this helpful?
Thank you for voting!
intermittent between low & high elements
-
Fred from Plymouth, NH
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
remove knobs and plastic nuts behind them, remove the six hex head screws holding switch plate, Remove two screws holding problem switch to plate. Swap wires one for one and reverse the process to complete repair. PS don't forget to turn off the range at the breaker panel.
Was this helpful?
Thank you for voting!
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
-
brendan from lebanon, NH
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections per
... Read more
iodically as to avoid another situation like this .
Read less
Was this helpful?
Thank you for voting!
one burner not working
-
Edwin from HIGHLANDS RANCH, CO
- Really Easy
- 15 - 30 mins
-
Socket set
Removed two screws to access burner. Removed three power clips from burner, reattached the clips to new burner, removed brace clips and attach to new burner, close lid and reattach stove cover.
Was this helpful?
Thank you for voting!
Oven lights were burning out regularly
-
Douglas from Thornton, CO
- Really Easy
- 15 - 30 mins
-
Socket set
Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixtu
... Read more
re back into place and screwed the housing into place.
Read less
Was this helpful?
Thank you for voting!
oven temp. was not what setting called for
-
John from Acme, WA
- Easy
- 1- 2 hours
-
Nutdriver
turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.
Was this helpful?
Thank you for voting!