JS630SF1SS General Electric Wall Oven - Instructions

All Instructions for the JS630SF1SS
61 - 75 of 87

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced cracked inner oven door glass
1 person found this instruction helpful.
  • Sherry from SAINT PAUL, MN
  • Easy
  • 1- 2 hours
  • Screw drivers
This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.
Was this helpful?
Thank you for voting!
Broke the glass on our oven door due to cold water spilled while it was hot
1 person found this instruction helpful.
  • Dagmar from WESTMINSTER, CO
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
First of all, there are FOUR panes of glass on the oven door and two different sizes. Make sure you're ordering the right pane. We initially got the wrong one and had to return/reorder.

Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful whe n putting it back together.
When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.

For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.

We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.
Was this helpful?
Thank you for voting!
Back burner was not working.
2 of 5 people found this instruction helpful.
  • Vilas from HANOVER TWP, PA
  • Really Easy
  • 30 - 60 mins
  • Pliers
Took top of stove off, disconnected the heating element, re-installed the new element and now my stove works fine.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people found this instruction helpful.
  • Louis from LEAGUE CITY, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy
Was this helpful?
Thank you for voting!
Oven will not heat
1 of 3 people found this instruction helpful.
  • Joseph from Homosassa, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low c urrent igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this helpful?
Thank you for voting!
Heating element burned out
1 of 3 people found this instruction helpful.
  • William from CONCORD, MA
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Followed example on YouTube! Very easy.
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people found this instruction helpful.
  • Roscoe G from ROCHESTER, NY
  • Very Easy
  • Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Open door. Put racks in.
  • Harriet from Jacksonville Beach, FL
  • Really Easy
  • Less than 15 mins
nothing to it.
Was this helpful?
Thank you for voting!
Stove drawer rear guides broken
  • Robert from Shakopee, MN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Installed new guides with a nut driver without any problems.
Was this helpful?
Thank you for voting!
I needed an oven with three racks, mine came with two.
  • BETTY from CYPRESS, TX
  • Easy
  • Less than 15 mins
just slipped it in
Was this helpful?
Thank you for voting!
Our bottom drawer support broke and the bottom drawer was canted
  • Robert from Woodinville, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this helpful?
Thank you for voting!
Missing oven rack
  • Damaris from Easton, PA
  • Really Easy
  • Less than 15 mins
I opened oven and pushed oven rack inside.
Was this helpful?
Thank you for voting!
no racks to oven
  • Johnette from Baltimore, MD
  • Really Easy
  • Less than 15 mins
Easily glide in.
Was this helpful?
Thank you for voting!
Oven temperature was low when reading was correct
  • Orion from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the b ack top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!
Was this helpful?
Thank you for voting!
Hard to move drawer in and out because the rear drawer supports broke off.
  • Steven from Lansdale, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this helpful?
Thank you for voting!
All Instructions for the JS630SF1SS
61 - 75 of 87