JP930TKW General Electric Range - Instructions

Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.

I went online and ordered the part after reading other people's repair experiences, confident that I could do it because the part was quite pricey. First, be sure you're circuit breaker to your range is off. Next, open the oven door and locate and remove two screws with a socket, that are just under the top surface which will allow you to ... Read more lift up the glass top which is actually hinged...no need to pull the range out. Securely prop up the glass surface area and the burners are exposed. With a marker, mark where each color wire goes on the burner you are going to remove and also mark where the two holding brackets are. This way you can reference the locations to connect to the new one. Carefully remove the wires and brackets and install new burner with brackets and connections. Close up the top, replace two screws, turn on breaker, and if there were no other faulty components,it'll work great. P.S Be gentle getting the very snug wires off. Good Luck

I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the ... Read more burner,
then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.

Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. C ... Read more onnected the wires and resecured top to base. Turned on the current and it worked beautifully.

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

Turn off breaker, disconnect electrical wiring, remove cooktop from courter top, turn over , remove switch.

after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips ... Read more was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.

Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and posi ... Read more tion them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.

turn off breaker, two screws hold down cooktop, 8 screws take top off cooktop. unplug switch, install new switch. repair loose connections. put back together. pretty simple

I removed the screws from the underside of the stovetop, lifted up the top, propped it up to keep it from falling (using a large book), and removed the old burner by unscrewing it from the top and removing the wire connections. I then screwed the new burner into the top, and attached the wires back to the burner, dropped the top down (ge ... Read more ntly and carefully, of course), and screwed the top back down to the rest of the stove. It was fairly quick and painless. Although, putting the stove back into his position was not easy, but that was no fault of the stove!!

Very simple repair. Remove two screws to lift the range top. Then remove the two screws holding the element in place. Disconnect the wires from the old element, connect the wires to the new element. Reverse the procedure and you are done. Total time is anywhere from 15 to 30 minutes.

I thought it was the burner thermostat, so I replaced the burner unit. By coincidence, the ceramic outer portion of the burner was cracked in two places, but otherwise intact. That was not the problem, though since the new burner did the same thing as the old one. Then I new it was the Infinite Control Switch, so I ordered it. Repl ... Read more acing it was easy. I turned off the cooktop circuit breaker and made sure no power was going to it. It is powered by 240 volts so you need to be very careful to turn off the power before doing any servicing on it. I then carefully pried up the glass cooktop and lifted it out, so it wouldn't break. By taking off the control knobs, and removing several small Phillips head screws all around the metal cooktop frame and just under the edge of the glass cooktop, I could lift the glass top off from the cooktop, and place it on some newspaper so it didn't get broken. It is important to keep the rest of the cooktop upright. The burners are not fastened down, and only gravity holds them in place. They normally sit on two springloaded pins, one on each side, and the weight of the glasstop pushes them down to their proper setting. So don't mess with them, and make sure each side remains on the two pins after you're done and before putting the glasstop back on. As for the switch, you need to remove two small 1/4 inch metal screws (a socket is very handy for this), one on each side of a metal framework that holds all the switches. After removing that framework, I carefully turned it over and found the correct switch for the burner that wasn't working. In my case, it was the closest right hand burner, which is also the biggest and has the option of having a big, small or both elements turned on, depending on how you turn the control switch. I then carefully pulled off each wire lead, with a needlenose plier to avoid damaging them, and immediately put each wire onto the corresponding same connection on the new switch. Take a close look at the wires on the old switch to make sure you plug them into the same connectors on the new switch. It's pretty straightforward. There may have been one or two small screws holding the switch onto the framework, but I don't recall right now. It was very easy to see how to remove and then reattach it. Then reverse the above steps and reinstall the cooktop, turn on the power and you should be in business!

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

Removed stove top from counter, removed glass top by removing 10 phillps screws, removed control bracked, unplugged connectors(wires) on old control and plugged into the correct position on the new control, replace control on the bracket then reinstalled the stove top and placed the stove top back into counter.

Pull out Range and unplug from wall receptacle. Open Range door and remove 2 hex head screws with pliers. Screws located at top inside of range door opening. They hold the burner top in place. Slowly lift front of top burner section up and at same time slightly lifting back of burner section since it rests on 2 pivots. Prop front of ... Read more burner section open, tilted back, with a piece of 2X4 maybe 2 1/2 ft. long. Make sure the 2X4 is located at the front/middle of range [resting on insulation] and at front middle of burner top to keep it opened firmly and balanced. You have about 5 or 6 wire clips to remove from elec. posts. Use pliers to gently remove clips. Tag the wires with tape to remember which wires go onto the new burner. Or take a close up picture with your phone to remember which wires go where. There are 2 philips head screws holding clips that hold the burner in place. The clips are slipped into a slot to help hold them in place. Mark the 2 slots so that when you remove the clips you will remember which slots to put them back into. You will need to hold the burner with one hand while you are removing the last clip as it could just fall out. Remove old burner and install new burner at same angle as was the old burner. You will have to make sure that the 2 clips are in the slotted openings first as you can not put them in place after the burner is installed in the opening. Reinstall the 2 screws into the 2 clips. Hold the electrical pole fittings with one hand while you gently reattach the electrical clips with a set of pliers. You may need to wiggle the clips back and forth to get them on securely. Remove the 2X4 and gently lower the burner top. The hardest part is now you have to slightly lift the back of the burner top while the front is lifted up and maneuver the back to drop down over the 2 pivots. Then the burner top will drop down in place so that the 2 screws in the range door opening can be reinstalled. I don't know of an easy way of making the top of the burner section fall down over the pivots except trial and error. Maybe use a flashlight to look back where the pivots are located while the top is propped open. That may help you visually to see what you are trying to do.