Models > JNM1541DM4BB > Instructions

JNM1541DM4BB General Electric Microwave - Instructions

All Instructions for the JNM1541DM4BB
46 - 60 of 73
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic cover had quarter size hole burned
Use a butter knife to pop small plastic pin out and turn to remove. Used the metal pinwheel from old one and placed it back up in the microwave. Never heard of this being possible, but it seems to happen per the website and many other comments.
Parts Used:
Stirrer Fan Cover
  • Judy from CAPE CORAL, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Food wouldn't heat up
Googled problem, removed diode, checked with meter and it was open, ordered new diode, checked new diode and it read open, installed. Any way, it didn't work. Went and bought new microwave!!
Parts Used:
DIODE-CABLE ASM
  • Ira from LIVINGSTON, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked plastic where the spring attaches
A 2 yr old could do this snap out. Snap in less then. 30 seconds . What a shame and rip off on appliance repair shops - I called to do this rediculsley 40 second job and the wantvv$125.00!9t more. Omg. I’m a senior/ no wonder God punished the world wit Covid 19! Too many nasty infair. Buii I needed and rip offs.
Parts Used:
Door Latch
  • Samuel from LAS VEGAS, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat. No unusual noise. Appers to function other than no heat
Multimeter checked/confirmed switches, sensors, and fuse first. All good. High power diode was bad - Replaced. Still no heat but now loud "MMMMM" noise when running. This means either the capacitor is also bad and/or magnetron.
Parts Used:
DIODE-CABLE ASM
  • Darin from SAN DIEGO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lawn mower would not start
removed cover over motor blew it out of leaves and dust. Removes 4 screws and removed piece ordered. The coil was rusted and not connecting. Changed oiece its working again
Parts Used:
Glass Cooking Tray
  • Lorraine from MIDDLETOWN, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very loud noise when cooking
I opened it up, found there is sparks on the diode when cooking, I replaced the diode first, still no heat, I found all the switches and thermal stats were normal, there is 120V AC input to the transformer, so I tried to make a good guess and bought a Magnetron from Partselect, after I installed the new Magnetron, there is heat and the microwave is working.
Parts Used:
Magnetron
  • Joseph from SANDY, UT
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan cover was melted with holes.
Simple fix. Prayed old off with flathead screwdriver. Installed new in less than 2 minutes.
Parts Used:
Stirrer Fan Cover
  • Jessie from PLAQUEMINE, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Screws weren’t included
Had to buy bigger screws to keep it from breaking again!
Parts Used:
Door Handle - Black COVER CHOKE
  • Marion from METAIRIE, LA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat
Also installed capacitor diode cable from first parts order. Used Phillips screwdriver to remove parts and reinstall. The original latch board becomes unusable when removing parts requiring the purchase of a new board. New parts did not solve the problem so it was a waste of time and money.
Parts Used:
BOARD, LATCH Primary Interlock Door Switch
  • Wayne from DENTON, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The 1st hardware kit I ordered had a missing alinement screw.
. The part arrived in acouple of days and the repair to minutes. Good work Jim.
Parts Used:
Installation Mounting Hardware Kit
  • James from Livermore, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken handle
Once I figured out how to access the attachemnt points, the replacement was easy.
Parts Used:
Door Handle - Black
  • Edward from Cranston, RI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken micro tray
placed plate on carousel
Parts Used:
Glass Cooking Tray
  • william from San Marcos, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven turntable rotating intermittent
Removed glass table. Lifted out shaft coupling. Replaced shaft coupling with new one and glass plate.
Parts Used:
Turntable Shaft
  • Stephen from Burnsville, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Parts Used:
Glass Cooking Tray
  • Pines, from Middletown, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Microwave would act like it's working but the turn table didn't spin and the food would not heat up.
Removed the top vent cover (2 screws) and removed the control panel (1 screw). Replaced the door's top interlock switch. The switch bracket tabs broke but a good zip tie worked just as well.
Parts Used:
Primary Interlock Door Switch
  • paul from strongsville, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JNM1541DM4BB
46 - 60 of 73
Back to Top