JGP933SEK1SS General Electric Cooktop - Instructions

I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.

I've replaced 2 igniters on this stove. My symptoms were that when I tried to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.

I first removed the top of the cooktop, which was 12 screws with a special star shape to them. Then had to pull the igniters out with some pliers (they have a really tight fit). Then remove the harness. Then I replaced the harness. After assembling, I replaced one of the ceramic igniters due to it being covered in baked on grease. Worked perfectly after that. I thank PartSelect for having super fast delivery. I ordered my parts on a Monday, they were at my doorstep the very next day, I was like WOW. And I chose regular shipping. Thank you very much for your service and your salespeople were VERY helpful, even after 3 order changes.

All I needed to do was replace the missing burner head and caps. Cook top is now back in service. Thanks for getting me the parts in a very timely manor!

A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

Do not remove the gas line.

Take off the burner racks and burner covers

Gently extract/remove the ignitors from each burner. You may have to use pliers, but be careful. They are ceramic.

Once you pull out the ignitors, you can remove the ignitors from their wires using plyers, you may have to twist them a little.

To take off the top - use Star screw drivers to remove the burners

Remove all the burners.

The star screws, and the burners are the only thing holding the top on.

Take off the steel top.

That exposes the ignitor switch assembly.

Make sure you follow the positioning diagram that comes with the new part.

Thats it really.

I removed the gas, because I thought I had to, but you don't need to. You can do the whole job in 30 minutes if you are careful.

Hope it helps.

You'll have to

Removed the burers using a torx wrench disconnected the spark wire then replaced the spark generator and the wire harness to the gas valves.
Installation went smooth and easy.
replaced the spark wire and re-assembled the burnners. very easy repair. replaced the sark generator though it didn't need it because I didn't want to un-assessemble the unit again at a later date.

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

Pulled the old one out. Disconnected the wire. Repaired the frayed wire cover with Liquid Tape. Connected the wire. Inserted the new part into the hole. This is after installing a new spark module earlier. But that was dumb easy too. So for about $100 bucks in parts and an hour of my time I saved myself the appliance repairman money and agonizing scheduling and dealing with them for the price of gold. I also replaced all the gaskets on the burners in that time. It so easy even a financial planner could do it.

I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part only coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!

I removed the burner head #152 and the Burner Cap #330, no tools are needed to remove these items. I pulled the igniter up far enough to get to the wire, disconnected and connected the new igniter put it back in place, reassembled the two parts plugged it back in and turned it on and it worked.

In order to replace the spark igniter switch and harness, order the appropriate model replacement part for your GE gas model. Turn of the circuit breaker if it is not already in the locked off position. Remove grates, gas covers, knobs and all from the cooktop surface. Unscrew all the screws with a clover tipped screw driver. Pull up and out on the 4 porcelain flints at each burner. Lift top up. You will see the part that needs to be replaced to your far right. Unplug it and remove it. Replace and connect the replacement. Reverse the process on opening the stovetop until everything is back in place as before. Flip your circuit breaker back on. Done.

Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.

Took longer to open the box.