JES831WB01 General Electric Microwave - Instructions

Replaced the fuse. Result; did not fix the problem.

Just put the new tray in and it fit perfect

Cannot believe how fast I received the tray. It was shipped from Lenexa warehouse, which is just 100 miles south of us so I received it in like nextday. Popped it in Microwave and was good as new. Will definitely order from parts select again. Thank you.

My husband wanted to use super glue to put it back together. I totally disagreed - googled the problem - order the replacement tray. It works great!!!

with one hand

I removed the outside cover of my microwave . ,It slides off , and the the burned out bulb was in a easy location ,and easy to remove, and then I replaced the new one then , replaced the outside cover, pluged in my microwave and bingo '''it was a sucess, and by the way I am 82 years old and like to repair things , so it saved me about 100. 00 With the walk in price of 65. 00. They charge you,, and labor it cost to replace the blub thank you for your promped service pat

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

I had a bad cut off sensor on oven cavity I ran the Microwave with nothing in it and it smoked I ran it for another 6 months then 1 day I was heating water and it stop- working. I put a new tube in might be Okay but I was not going to risk it taking another cut off sensor on overload. You have to change sensor and put on a new tube. Clearly it would be cheaper to buy a new unit but it was only 2 years old and I am an old tech and was curious. The sensor cost only 16 bucks new tube about 55 a replace brand new oven 81 bucks there you have it I was stubborn and going to get that sucker back into operation I had another oven go out the same way

As easy as putting the tray inside the microwave. Part fit perfect!!

20 month old GE m/w had made "electrical" smells from beginning. Finally unit failed to turn on. Disassembly was easy except that I needed to buy anti-tamper screw driver bits from Sears to remove two screws. Found the blade connector to the sensor was a loose fit, resulting in severe heating at the connection. Plastic connector was melted and sensor was damaged to the extent this seems a possible fire hazard. Replacing the sensor is trivial, and requires removing one Phillips head screw. Reterminating the defective connector requires basic electrical skills; wire stripping and crimping. Be sure to clip a few millimeters of wire to get undamaged copper. Be sure to replace both connectors if connections feel at all loose. M/w reassembly is trivial.

I googled "Microwave stopped working", and after reviewing numerous websites with suggestions, I found the response noted below at "Help Owl" which was the most straighfoward and clear explanation to trouble shoot the problem. I first tested the Thermal Cut Out (TCO) per the instructions below and that was the problem. I didn't have to test the electrical fuse. Turns out that you cannot typically use the microwave continuously for more the 12 or 13 minutes or it may overheat and the TCO will shut it down. Extremely easy to test for and fix, and the part is only $15! See Trouble Shooting steps as follows: Make sure that the unit is vented properly and that if you are using it for prolonged periods while cooking, that you turn-on the vent fan.
If there is no display / power within the unit...first check your power source where you plug the unit into the wall.

If that is good, Remove the Cabinette/Cover "Note: it has 3-Torx Anti-Tamper Screws".

Then as you face the microwave from the rear, at the left rear corner is a small circuit board with a fuse. "Check the Fuse"

If the fuse is good, Check the following:

1 - The most common component failure is the "Cabinette TCO" (Thermal Cut-Off Thermostat).

As you face the microwave from the rear...It is located under the cover, on top, on the left front corner area.

It is a Circular, Black & Silver Disc Shaped component about the size of a dime in diameter and is about 1/2" in height.

It has Two (2) Wires attached to it's spade connectors and it acts as a safety fuse.

"IF YOU PUT AN INSULATED JUMPER WIRE ACROSS THE 2 TERMINALS THE POWER SHOULD RETURN AND THE DISPLAY WILL LIGHT"

Anything other than these two items should be checked by an Authorized Service Technician as these microwaves have components thay carry "HIGH VOLTAGE SHOCK HAZZARDS"

bought a fuse but that didn't solve the problem. Guess I need a new microwave

It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.

Remove cover-the hardest part, as I needed to buy a new set of driver bits that included the dimpled security drivers to remove three screws. GE includes schematic and troubleshooting flow chart with the unit, taped inside the cover. Required more time to look up the part on-line and order it than time used to make the repair.

I removed the cover this required a special star Apex tip witha hole in the center. $10 for a set at Lowes.Replaced the fuse and Thermal cut out at the same time. The oven woks like a charm.I would like to add that GE customer service was no help basically told me that it was a throw away unit. If they built it you can fix it.Hope this helps any DIY breathern outthere.