GT2413NXFW Amana Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
light not working in fridge
It was so easy!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Easy!
And I am not Mr. Fix-it!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Easy!
And I am not Mr. Fix-it!
Parts Used:
-
Michael from East Meadow, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken shelf supports
It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.
Parts Used:
-
vickie from Acworth, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old seals around doors were leaking cool air.
Easy as could be. Unscrew the bolts on the inside of the seal, take off the old seal, place new seal on and screw back in. Saved myself $150 by doing it myself. So easy, my 7 year old could have done it.
Parts Used:
-
Jeff from Crownsville, MD
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Condenser Fan Motor seized up
First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!
Service and shipping were fantastic! I would definitely use Partselect again!
Service and shipping were fantastic! I would definitely use Partselect again!
Parts Used:
-
Peter from Herndon, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer will not freeze or cool the ice box
I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson
Parts Used:
-
David from Choctaw, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
8 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Parts Used:
-
Antonio from San Antonio, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Parts Used:
-
Duncan from Metairie, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
refrigerator not cooling properly
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.
Parts Used:
-
Ernie from Windsor, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old gasket leaking
The gasket is sandwiched between the main door and the shelf assembly.
What holds them together is 42 1/4in hex head self tapping screws that run along the edge (each one is finger tight).
I would highly recommend a power drill with a 1/4 hex socket to remove the screws. It makes things much faster. Be careful when screwing the screws back in with the power drill(you only want them finger tight). If the screws are too tight,the gasket will bulge out in places.
At first the seal may feel weak. Keep the door closed for a couple of hours and the seal should improve.
What holds them together is 42 1/4in hex head self tapping screws that run along the edge (each one is finger tight).
I would highly recommend a power drill with a 1/4 hex socket to remove the screws. It makes things much faster. Be careful when screwing the screws back in with the power drill(you only want them finger tight). If the screws are too tight,the gasket will bulge out in places.
At first the seal may feel weak. Keep the door closed for a couple of hours and the seal should improve.
Parts Used:
-
Laurence from San Diego, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Socket set
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Parts Used:
-
Dave from Manchester Center, VT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Glass shelf broken while being cleaned.
Ordered new shelf on a Tuesday night. Part shipped out on Wednesday, received and installed on Friday. It doesn't get any better than that!
Parts Used:
-
Kenneth from Titusville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked Gasket
No need to repeat the other directions, everyone is spot on with exactly what to do, the ONLY thing I want to add is that prior to putting the new gasket on, throw it into the dryer for a few minutes to make it more pliable..... My problem was that it didn't seat very well, be patient, after 2 days and keeping pressure on it over night, it was a perfect fit !
Parts Used:
-
Robert from RIO GRANDE, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing Door seals on freezer/fridge doors
I removed the top door hinge plate and removed the door (it is much easier to do this with the door removed. I put all the food into an ice chest and that made a hardy work area to set the door on and remove the screws holding the inner door and seal. This type of seal requires you to remove the screws completely. Still not satisfied with the way the new seals close, however - the magnet stips in the old seals were stronger.
Parts Used:
-
Ronald from San Diego, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
evaporator fan was noisy
First I unplugged the refrigerator. Next item was the ice-maker; remove (3) screws and unplug it from the back wall. Third task is remove the (4) screws that attach the back wall of the freezer compartment. Lift the wall up enough to dislodge the center cooling shaft that the fan rides in and remove the rear wall. The last item is the fan motor which is attached to the freezer wall by (2) screws and (3) wires which are easily removed. Change out the motor and reassemble freezer compartment .
Parts Used:
-
Dwayne from Gastonia, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
6 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Parts Used:
-
Winston A from Brooklyn, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!