GT1928PAGW Maytag Refrigerator - Instructions

Removed the inside door panel. Removed old seal. The new seal was very wrinkled so put it in the clothes drier for 10 minutes . Then stretched it on to the inner door panel and reinstalled it to the door. Not as good a fit as I'd hope for but it will do the job

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Very easy to order from parts select. Took seconds to replace.

Instructions were great five minutes to remove and replace fan....Thank You............ saved big money

Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.

The drawer guide mounts in slots on a bracket hanging below the shelf above. Only had to use a screwdriver to move the plastic tab in the slotted bracket then slide the whole plastic guide out. ordering the new one was easy, cheap, and quick through PartsSelect.com. The new part just popped in without tools. Very easy!

1-Removed drawer; removed drawer shelve which contained rails; slid old rail out of shelve mounts with light taps on ends.
2- Screwed on the new rollers to rail guides; reinstalled new guides into shelve mounts; re-installed shelve onto mountings in refrigerator; re-inserted drawer nto new rails-Done!
Received parts 48 hrs. after placing order!
Great job! Third positive experience with Parts Select.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Everything just snapped in easy.

Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.

No repair needed. I had only to wash the new ones and use them.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

When the new glide rail didn't look any different that the one I thought was broken, I thought I'd assessed the wrong broken part as everytime I tried to put it in the slots it would still fall off, just like the old one.. But I went back and reread the other repair stories to get a picture in my mind what they were talking about. I realized I needed to get the glass shelf off but it wouldn't budge. I found the original information booklet and realized the two blue clips in the shelf tracks were nothing more than packing clips (we've had the fridge 8 year.) when I got those off (these took the most time and a flat head screwdriver) the shelf came right off. Then I put the glide rail brackets in the appropriate slots, pushed the rail toward the front of the shelf and when it got to the place of resistance, I just applied steady, gentle pressure to get the brackets to lock in place in the slots. Repair done, placed shelf back in fridge, put drawer back on, and it was done. Oh, forgot, I first had to take the little wheel thingy off the old raid and screw it onto the new rail before attaching the new rail to the shelf. By the Way, this was really easy to do. I'm a 66 year old grandmother and this was my first refrigerator repair. Always read the previous repair stories--they really do tell you what you need to do.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!