GSE23GSKRCSS General Electric Refrigerator - Instructions

Great Service! Received the part the NEXT DAY!

We originally called a service technician. He came the next day and said the mother board was no good. He order a new one and replaced it a week later. Total part & labor cost: $185.00 (Remember we're without a working refrigerator the whole time the part is on order)
Two days later the freezer is doing the same thing. We call the tech again and he seems confused and says it could be the heating element, he'll order one at no charge and replace it for us free. He never comes back with the part and does not answer our 2 dozen phone calls. I checked the element myself and saw that the tube had been scorched, like a burnt out light bulb. Searched for parts on internet and found this great site. "Partselect.com"
REPAIR:
Refrigerator had been unplugged for a few days to defrost ice build up in freezer. First, I removed the shelves from freezer compartment, removed the back panel and removed screws holding heater element in place, I unplugged the two electrical leads and plugged in new part. AS EASY AS THAT !!!!! I reinstalled the screws to hold the element, installed the back panel and replaced the freezer shelves. I plugged the refrigerator back in and within hours the freezer started making ice again. It's been about 3 weeks and we have not had a problem since.
Fantastic Service and instructions and Inexpensive !!!! I will use this site again, if needed, and will recommemd to anyone who needs parts.

We just bought a new home and found that one of the clear shelf inserts in a door shelf was pretty much trashed. I was very pleased to be able to find this part at this site . Instead of having to replace the entire shelf I could just put in this part. My only comment is that this clear part is rather difficult to get into the white plastic shelf. I was afraid I was going to break it. But it has to fit snugly. The final result is very nice. Just be aware that these clear shelf inserts do not go in easily.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

The door stop is held by 2 TORX screws and can be removed in place without raising the refrigerator. The only tricky part is that you only have about 2 inches of clearance so it is hard to locate/see the screw heads. I used a small mirror to help me align the tool with the screw. If you have a small ratchet with a TORX socket it will make your installation go much faster. Each turn of the tool required me to remove and reinsert the tool. This is what takes up so much time.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Needed to remove and replace the door stop. It was held on by tow screws that are about 3 inches from the floor. God a hex driver and small ratchet to hold the hex head. unscrewed the old and replaced the new. I did take a picture with my phone and it showed the two screws.

I just moved the moving parts from the Frame for the humidity level from old to new and all was OK

Clear freezer items in the area of repair as light assembly is in the back of the freezer. Suggest removing shelving in the same area to provide more working space. Utliize a small flashlight to provide interior lighting. Use a stubby phillips screwdriver to remove fastener securing the light cover.
Cover snaps out to remove light board assembly. Gently pull to disconnect the electrical connection to the light board. Then pull the light board assembly from the mounting posts securing the light board. Be careful not to snap either posts or the light board.
To install the new light board, I found it easier to connect the electrical source first, then push the light board onto the plastic posts to secure the light board. There are holes in the light board to insure a secure fit. Reinstall the light cover and reinstall the mounting screw. All done in less than 5 minutes!

Unplug refrigerator. Use nutdriver to take two srews out that were holding on the housing. Unplug electric plug and pull out motor and housing. Use hacksaw to cut thru auger holder. Motor will be free to take off,disconnect two wires. Use nutdriver to take out three srews holding motor. Take back cover off and put new motor in cover and reverse procedure. Used new auger wih new motor. Saved big bucks by during this job myself.

We opened the box, unpacked the drawer, washed and dried it, installed it! No muss, no fuss!

Simply removing parts from the old frame and installing them on the new frame and putting everything back in the refrigerator to include the glass.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

Manually inserted new refrigerator module inserts

slide in place

Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.