GSE23GSKRCSS General Electric Refrigerator - Instructions

Unplugged the fridge, and opened the freezer. Unscrewed the light panel, small screwdriver. Removed the plastic bracket. Part was frozen and I broke one of the plastic mounts. Do not do this as I am not sure if I will have to live with my cable twist tie kludge or I can get another plastic bracket. Light board is just the PCB. You need to remove the old PCB and install the new one- remember the orientation and the fact that the plastic mount piece has specific sides you can identify by the width of the slots. This is for all the other women like me. Thanks.

the replacement part did not have the 3 screw holes needed to 100% replace the part that broke. however, i realized that the piece that fastens to these 3 screws is the slider cover piece (i dont know its name) that has the rubber gasket was sticking every time i opened the drawer and this was what caused the OEM part to break. anyone who has a GE profile with the meat compartment must know what i am talking about - it sticks and is a bit clunky to open (until the pressure breaks the pin holding the gasket as in my case).
i simply did not place that piece back when i put the replacement part in, and now it slides much more easily. the downside is slightly less seal for the meat compartment, but to me that isnt very important because that compartment does not need to be isolated from the rest of the fridge to do its job.

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!

1) Unplug Refrigerator. Remove all shelves and light shield in the freezer.
2)Remove panel covering refrigeration coils inside freezer in back. Two hex head screws w/nut driver.
3)Remove the defrost heater using phillips screw driver. Two screws.
4)Unplug two quick disconnect stakons and wires from heater.
5)Plug the wire coming down the right side into one side of the new heater and plug the shipped white wire into the other quick disconnect spade at the heater.
6)Install the new dual element defrost heater into the same place where the old was. Connections to the right.
7)Route the wire that was on the left across the top of the coils and down the right side.
8)Bring the existing wire from the left side down the right side and the white wire up the right side. Wires should not be tight at all and do not remove the tape at the stakon.
9)Now wires need to be cut (if necessary)and crimped together in the shipped stakon. This stakon looks like a wire nut.
10)Wires should be tucked gently into the styrofoam up and down the right side. Wirenut should be positioned so that water can not collect in it.
11)Replace the panel over the cooling coils.
12)Plug Refigerator back into the wall outlet. Put shelves and light shield back in.
13)My refrigerator is now working without a problem. It's been est two weeks.
Ice maker is also working correctly.

I removed the old shelf and installed the new one!

The new shelf went in really easy. It just fit in the alloted slot.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

unplug refrige take off light cover unplug lightbar and take lightbar off bracket put new LED lightbar back on the bracket and attatch back on back wall of freezer put light cover back on plug in refrige done.

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

Emptied the door bin, removed it from its slots, and gently spread the plastic bin sides allowing the broken face panel to fall out. Replaced one end in the notches, gently widened the opening at the other end to slide the new face panel in, and jiggled just a little to seat the panel fully. Done!

1. Removed the back panel of the fridge to get access to the inlet water valve.
2. Removed black poly water line from valve (pull back on white ring where line is attached and pull the line out)
3. Removed the inlet tube from top-back of fridge (where it goes into the ice make). use putty knife to get under the sticky white gasket beneath the black oval housing and pull the tube out form the back of the fridge.
4. Replace the water line with new part taking care to properly seat the line into the the bottom water valve and pushing the water tube into the hole for the ice maker.

Note: Be sure to take off the protective covering from the white - sticky grommet and push to adhere to metal on fridge.

to be safe - use a bit of clear silicone chaulking round the perimeter of the grommet and push to tighly bond the water inlet tube to the fridge.

The reason for this - is that if you do not get a good bond using the white - sticky gormmet alone - you may have the water tube inside the ice maker freeze up.

Also once the new water line is installed be sure to secure the line to the metal back of the fridge - so the line will not move. some fridges come with metal hose clamps to do this - otherwise use duct tape

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

Repairs on purchase of the parts were easy and went great

Watched a parts.com video on how to change defrost thermostat and followed the instructions