GS2726CEHQ Maytag Refrigerator - Instructions

Removed the door assembly with 4 Torx screws, replaced the broken door with the new one. The assembly is spring closed, so had to be pivoted into place. Then the door didn't open when the ice button was pushed, but made a loud snapping noise. After removal again, it was determined that the solenoid was not attached properly to the arm. After this was done and the whole assembly was put back on the door, everything worked fine.

Watch out for the circuit board at the front of the assembly, it carries a pretty good bite!

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Very easy to order from parts select. Took seconds to replace.

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

I removed the broken ice bucket support enclosure using the nut driver and screw driver. The new part had to have the ice bucket motor attached. The metal piece that attaches to the motor shaft had to first be removed, which was somewhat difficult (careful! the thread is reversed). The motor and spring assebly had to be re-attached to the new ice bucket support enclosure piece.
This repair was relatively easy.

Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.

Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!

removed one holding screw (left side center}, used pliers to hold motor shaft so I could unscrew auger drive fork (counter clockwise), then unscrew two screws for ice bucket door magnet push lever, unscrew four screws to auger motor and toss damaged ice bucket support enclosure and don't forget to screw in that one holding screw on lower left side .. then remount both components onto new thin plastic ice bucket support enclosure ... reassemble remaining ice bucket right side wall and slide in main ice bucket with auger. Not a big fix, but part & shipping was just short of $80 ..

1. Unplug refrigerator and remove fountain drip tray.
2. Remove the two #15 torx head screws that were covered by the drip tray.
3. Pull the bottom of the trim panel out and push up to remove panel and then unplug switch circuit board connector..
4.Remove the three screws (same size as the other two) and then remove the switch, ice door, etc assembly and unplug the connector.
5. Aside. At this time I extended the water hose which has been short since new. Used a couple of inches of 1/4 inch plastic tube. Heated it with boiling water and slipped it over the existing tube to extend it about 1/2 inch. Now the water flows in a uniform predictable stream.
6.Remove the tiny phillips screw holding the switch in place.
7.Remove and replace the old switch and actuator pad and screw. Check operation of switch. I lubricated the surface between the switch actuator bar and the rubber with a little plastilube(white) grease. Probably highly optional.
8.Replace and replug the assembley. Tuck the actuator pad around the edges if needed. Remember to turn the screws CCW until they fall into the old threads and then tighten them until snug.
9.Plug in and mount trim and connect refrigerator.

removed three nuts from the top of the door diconected the electrical connections for the ice and water in the door. Removed door by lifting it up about 2 inches, set it aside put new hinge pieces in placed put everything back together. writing this took more time. wanted to add, bought at 2 pm on thursday was at my house by 10am the next day

disassemble the front panel removed two screws and panel fell forward took old part out cliped in new one and reassembled very easy job

It is the model with the french door. I unplugged it, removed two screws at the bottom of the door, while holding the door from sliding down. Removed the door and put it on its side. Removed one screw that was holding the hinge, removed the hinge and replaced it with the new one. Put the door back on (do not forget to reinstall the shims).
Did the same thing on the other door. After putting the door back on readjusted the height to level the door, using height adjustment screw. Lock the door in place. It now works better then new

First I removed the two screws to remove outside cover. Then removed three screws to the ice dispenser assembly. Slipped in the new round door assembly and replaced the removed screws. No problems.

We removed the old part, which actually looked quite functional. We put on the new part, thinking that the repair was not going to be effective, and that we were going to need other parts. But, the refrigerator is working perfectly now, and I have no more run-ons onto the floor. THank you very much.

The repair was relatively easy. After the ice tray is removed. The plastic box holding it has 3 screws holing it. After those are removed, the tray will begin to slide out. You need to unplug the controls at the back and then the old tray can be removed. The old plastic could then be removed from the ice auger motor. The solenoid is removed from the tray with 4 screws. The only challenging part was removing the ice auger spindle. I was warned that it had reverse threads, and I may need to hit it with a hammer. However, I needed to purchase a thin set of vice grips to hold the shaft, while I turned the auger spindle. It took quite a bit of umph the get the thread connection to move. Re-installation was easy after that.