GS2125CEEW Maytag Refrigerator - Instructions

Step 1 :I had to remove the ice drip tray just pull it out.
Step 2 remove the 4 or 5 screws holidung in the control module (push button display pad)
step 3: pull the plug from the diaplay panel
Step 4: remove broken door from slot and slide new one in. Be carfull not to let the brass plug fall out of it does it just slides back in.
Reverse all steps your done about 20- minutes..I am a building engineer by trade. I think the average person 30 to 60 minutes..

removed the ice chute door, unhooked the computer board replaced the flap. The only problem was the spring loaded part of the ice chute door come up and the little plunger came loose. It only took a few minutes to replace the plunger back in the holder and replaced the ice chute door. The best part of the whole job was that I ordered the part on Monday afternoon and the part was at my door Wednesday. The Parts did an excellent job of getting the part to me quickly.

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Part selects cataglog for parts selection was very easy to use and the online service and delivery was great.
When I got the part, it was not apparent on how to remove the auger so that I could insert the new connector. There were about about 8 visible screws, with star drive heads that I fortunately had a screwdriver that fit, and I could not tell if I had to remove all of them or only a couple.
I ended up removing all, but still could not separate the dispenser portion which held the front of the auger from the back of the ice bin. I finally figured out that the dispenser door trip lever had to be disconnected and I almost lost it when I removed the metal clip that attached it to the outside of the ice bin when the spring loaded lever tried to unwind. I managed to hold it in place, separate the dispenser holding the auger from the rest of the ice bin and replace the connector. I them got the pieces back in place and was able to refasten the spring loaded lever and then replace the screws.
If the spring loaded lever had unloaded, it would have been tricky to try to replicate the amount of turns (load) on the spring tension.

Had to disassemble ice maker to install part. . .

googled for answer, deduced relay/switch problem. googled again for parts, found partselect.com, ordered part. 2 days later & $70 lighter, my 8yr old Maytag was working again! Parts were good fit, instructions were decent enough. Not for inexperienced tinkerer though.

Discovered ice door tab was broken. Ice door out of position.
Disassembled door dispenser, pretty easy, two torx screws on bottom, two on upper part of unit. Slid unit up slightly, it sets over two studs on the top. Unplugged wire connector, set aside unit. Looked on internet for a replacement part. These folks had the easiest to use web site. Found the part, ordered the part, received it next day, but only ordered the least expensive delivery method, since we are both in Florida it worked out well.
I did not know when I ordered this part I would get it this quickly. Because cold air was pouring out of the hole left by the removal of the ice door, I put wide painters tape over the hole on the inside of the freezer door. This greatly reduced the flow of cold air.
After I received the part, I clipped it in place and reassembled the unit, it did not work. The solenoid that moves the door just hummed like it was jammed. I took it back apart and realized that I did not get the bracket that moves the ice door reattached properly. After I made sure the bracket was properly attached, i reassembled the unit and it worked great. It actually took longer to type this description than it did to do the job.
Good Luck, Mike

I followed the instructions supplied by others on your site .They were right on. The repair was simple with the instructions. The service was absolutely superb. I ordered the part one morning.
The next morning Fed EX delivered the part to my door. I will use your site for parts from now on.

The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through the tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!

Removed the rubber gasket and checked the switch. The switch displayed signs of scorching and the plastic was very brittle. Removed the switch which was held in by a small bracket and one screw. Replaced switch on bracket and remounted the switch. It took longer to reinstall the rubber gasket that to diagnoise and repair the switch. This was a very easy repair and the time from the part order to receiving it was two days. I'm very pleased with the part availability and quick shipping.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Removed the door assembly with 4 Torx screws, replaced the broken door with the new one. The assembly is spring closed, so had to be pivoted into place. Then the door didn't open when the ice button was pushed, but made a loud snapping noise. After removal again, it was determined that the solenoid was not attached properly to the arm. After this was done and the whole assembly was put back on the door, everything worked fine.

Watch out for the circuit board at the front of the assembly, it carries a pretty good bite!

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

I went straight to PartsSelect on line and within minutes I found the appropriate brand of parts for my refrigerator. I simply removed the old trim shelf and snapped the replacements in place. I also inserted the glass shelf trim. No tools were required.