GS2125CEEW Maytag Refrigerator - Instructions

Pretty simple really...take out a couple screws and the face plate comes off. Take out the dispenser apparatus behind the face plate and you will see the little lever operated switch that activates the dispensers. Mine had one terminal slightly discolored like it got hot...so that is a good clue. Also, the whole system is pretty simple really, and the switch was clearly the culprit. I got the replacement switch from PartSelect in just a few days, and put it in. The whole deal only takes about 1/2 hour cradle to grave. The dispensers work fine now, and I think I saved at least $150 for a service call. BIG PAPA small

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

I found and ordered the parts, printed off instruction. We received the parts 2-3 days later. My husband went off the instructions I printed off and repaired the ice chute door. It works great. Finally a nice feeling and not complicated. My husband was impressed that I found the parts so easy and that he fixed it. I also had ordered the return spring and strike. We did not use them, but thats ok. Through parts select and how easy to order and get instructions we saved a lot of money. I definitely would use partselect again. Thank you.

Removed Control plate first. Second, I removed the next section behind the control plate. Inserted the new striker and reassembled.

Unplug the unit. Remove two screws under drip plate. Lift up control panel and slide off the ribbon plug on back of panel. Remove the shoot guard at bottom of ice shoop by taking out the two screws. Remove the two screws that hold the shoot assembly and pull panel out. Be careful of the water line and wires on the left side of panel. Shoot door slips into grooves on either side of solenoid rack. Be sure to get solenoid plunger back into bracket and reverse the procedure.

Stopped by a local repair shop to buy a crisper glass shelf for my Maytag refrigerator. Maytag does not sell the glass shelf, looked online and saw Repacements Parts.com. Ordered the shelf. Very happy customer!!!

I pulled the dispenser bin and emptied the existing ice (the maker worked, the dispenser would not dispense). Though there appears to be more, there are about 4 (reciting from memory)very small tap screws holding the front of the dispenser unit to the bin. The dispenser activation screw mounts over protruding items at each end. The item at the back (away from the dispenser gear package) is the drive ring that was broken. The drive ring is a small plastic cup that inserts into an opening at the back of the bin (female side to the rear) and slides into the distal end of the activation screw on the same end. One must line up the small slot on the inside of the drive ring with the end of the screw. Slide the assembly together (make sure that the cube/crush switch rod is properly clipped in place with the return spring hooked to the clip), GENTLY install the 4 or so screws and return he assembly to the freezer. It should work flawlessly. Elapsed time: 15 - 20 minutes.

Checked the ice tray and could only find the drive ring had some breaks in the plastic. Actually did not see why this would stop the auger from turning and dispensing ice. However this was the only thing I could find wrong with the unit. I pulled the tray, removed 6 screws (star tip heads) pulled the auger forward and replaced the drive wheel, put the unit back together and its been working fine ever since.

Getting a new lower hinge pin, fixed the problem.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

took of the face plate of the ice maker and disconnected the elec. strape and wire and removed the unit in order to replace the 3 parts...it was somewhat simple... Copied part select schematic in order to follow the part install sequence.

Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.

unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.