GFSS2HCYCSS General Electric Refrigerator - Instructions

All Instructions for the GFSS2HCYCSS
106 - 120 of 346

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Defroster fan burned up
3 of 6 people found this instruction helpful.
  • Peter M. from Lincoln Park, NJ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.
Was this helpful?
Thank you for voting!
icemaker quit working when we moved
4 of 10 people found this instruction helpful.
  • Regina from Taylorsville, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After wo rking with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!
Was this helpful?
Thank you for voting!
Freezer was running warm
1 person found this instruction helpful.
  • Richard from Bradenton, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.
Was this helpful?
Thank you for voting!
Everything freezing in fridge
2 of 4 people found this instruction helpful.
  • lois from hesperia, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
This was generally an easy fix. The work was in such a confined area of our side by side and my husbands shoulders are broad so that was a little more challenging but overall a quick, easy and cheap repair doing it ourselves without having to call a appliance repairman.
Was this helpful?
Thank you for voting!
Our side by side refridgerator the freezer side was freezing up.
1 person found this instruction helpful.
  • David from UPPER SANDSKY, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
After turning off power and unthawing back cover so I could remove it. Then I had remove all of the ice from the coils with a hair dryer. After everything was unthawed I removed the temperature sensor from the coil tubing and cut the wires. I skinned the wires on the new sensor and crimped a butt splice on each wire. I skinned each wire in the freezer then crimped butt splices to each wire. After taping the connections with black tape I reinstalled the back cover and turned on the power. So far it has been two weeks and there Is no frost and the refridgerator is working fine.
Was this helpful?
Thank you for voting!
Refrigerator door mullion was broken and loose making it difficult to close the left side door.
1 person found this instruction helpful.
  • cindy from Salisbury, MD
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed screws on broken mullion at top and bottom. Save screws; you’ll need them. Disposed of broken mullion panel. The wires from plug had severed and were dangling at the bottom. Removed the plug inside small opening at bottom of door using needle nose pliers . Held new mullion up to left door, lining up screw holes at top. Screw ed in top screw first. Pulled female part of plug out of small opening; removed male plug. Inserted new plug located on mullion in and pushed plug back into small opening. Installed one screw at bottom. The second screw at bottom wouldn’t line up so didn’t use. Installed second screw at top. The new mullion panel functions perfectly, seals well, and works great!
Was this helpful?
Thank you for voting!
Information on control center not lighting up and not running.
1 person found this instruction helpful.
  • Tommy from Malakoff, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Replacement was easy. Once new board was installed I let run 24 hours and the compressor would not cycle off. Unplugged for 5 minutes then plugged back in to reset. Operates correctly now.
Was this helpful?
Thank you for voting!
Staying on defrost too long. Ice melting and as a result ice maker not working do to re-freeze
1 person found this instruction helpful.
  • Paul from TOMS RIVER, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Per vidios
Was this helpful?
Thank you for voting!
defroster thermostat was bad
1 person found this instruction helpful.
  • ralph e from CARYVILLE, FL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
take the metal cover off the defrost thermostat is on top of the coil take the thermostat off from the coil cut the two wires take the wire and strip the ends off take the new thermostat the wires are color coded wire them together put the thermostat back on coil your done real easy
Was this helpful?
Thank you for voting!
Loud Squeal when fan was running
1 person found this instruction helpful.
  • Daniel from BURNEY, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.
Was this helpful?
Thank you for voting!
Frosting up in freezer ice freezing solid
1 person found this instruction helpful.
  • Ken from THE VILLAGES, FL
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Took out freezer rack took off the back panel also light bulb found the DEFROST THERMOSTAT cut the 2 wires remove the thermostat strip the wires on the new thermostat splice the to wires together with wire nut wrapped wire nuts with electrical tape put new thermostat back were the old came off of put panels back in place also the racks an d bulb plunged in the power and guess what it works like a Champ with in 1 hour making ice and going through defrost cycle nice Thank You Guys for your video and the how to do Thanks Ken
Was this helpful?
Thank you for voting!
Freezer was not defrosting. Ice accumulated inside of the back of freezer.
1 person found this instruction helpful.
  • Alcides from WINNETKA, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them to guether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks
Was this helpful?
Thank you for voting!
Wasn't getting cold and wouldn't defrost
1 person found this instruction helpful.
  • DeMarcus from Garrison, TX
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job
Was this helpful?
Thank you for voting!
I just wanted an extra door shelf
1 person found this instruction helpful.
  • Therese from MOUNT ANGEL, OR
  • Very Easy
  • Less than 15 mins
My need for a part wasn't about an appliance repair, it was about making my GE frig work better for my particular needs. There is a lot of wasted space in the 2 door (French door?) model, at least for me anyway, and so when I discovered your company, online, just by googling, I jumped at the opportunity to buy an extra shelf to use t he space more effectively. I was surprised. Package came quickly and installing it took a mere minute. I should have done this years ago! I am one happy camper. Excellent service, excellent quality shelf. Thank you everyone at PARTSELECT
Was this helpful?
Thank you for voting!
Runner on old drawer broken
1 person found this instruction helpful.
  • Arthur from INDIANOLA, WA
  • Very Easy
  • Less than 15 mins
Received new drawer, washed same, removed old drawer and transferred items to new drawer, THEN with out further ado reinstalled same!!! Wa La all finished.
Was this helpful?
Thank you for voting!
All Instructions for the GFSS2HCYCSS
106 - 120 of 346