- Home
- GFSS2HCYCSS
- Instructions
GFSS2HCYCSS General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Deli drawer broke off, probably loaded to heavy
3 of 3 people
found this instruction helpful.
-
esther from PELHAM, NY
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed the divided glass shelf, to which the slide rail is attached. Removed the broken rail, saved the two screws.
Now comes the clincher:
It would help if the replacement part website would tell you what size and what kind screwdriver you will need, so you could start chasing it while you wait for the part.
Even better ... Read more if they could include it, since the plastic part and it‘s shipment is not exactly cheap.
So to screw in two screws you need a #15 Star screwdriver!
How many housewife’s have this one in the tool drawer?
Now comes the clincher:
It would help if the replacement part website would tell you what size and what kind screwdriver you will need, so you could start chasing it while you wait for the part.
Even better ... Read more if they could include it, since the plastic part and it‘s shipment is not exactly cheap.
So to screw in two screws you need a #15 Star screwdriver!
How many housewife’s have this one in the tool drawer?
Read less
Was this helpful?
Thank you for voting!
Defrost cycle would not cycle off
6 of 13 people
found this instruction helpful.
-
anthony from Hampton, NJ
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Replaced Defrost Thermostat. Tricky removal of light fixture cover and evaporator cover. Light cover screw removal is not intuiitive and the eveaporator cover tabs are not easy AT ALL to remove.Once they are removed, simply 2 screw removal of rear panel.
Had to unscrew screws holding cooling coils to gain access to thermostat ... Read more mounted on a coil in rear.
Simkple matter to cut wires, remove old thermostat and splice replacement back on. Found it simpler to re-mount thermostat on top coil greatly simplifying process.(Why didn't they place the original unit in this much more accesible place?)
Re-attach coils to rear wall replace rear panel, light fixture cover and evaporator cover.
Refrigerator has been running fine this past week.
Received parts NEXT DAY! FANTASTIC!
Had to unscrew screws holding cooling coils to gain access to thermostat ... Read more mounted on a coil in rear.
Simkple matter to cut wires, remove old thermostat and splice replacement back on. Found it simpler to re-mount thermostat on top coil greatly simplifying process.(Why didn't they place the original unit in this much more accesible place?)
Re-attach coils to rear wall replace rear panel, light fixture cover and evaporator cover.
Refrigerator has been running fine this past week.
Received parts NEXT DAY! FANTASTIC!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
condenser icing refrigerator warm freezer ok
3 of 4 people
found this instruction helpful.
-
Rene from HEBER, CA
- Really Easy
- 30 - 60 mins
-
Pliers
follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new
Was this helpful?
Thank you for voting!
switchlight on my refrigerator was not working
5 of 10 people
found this instruction helpful.
-
Eileen from Coto de Caza, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point,
... Read more
it was just a matter of plugging in the new switchlight , which was very simple.
Read less
Was this helpful?
Thank you for voting!
icemaker stripper fall a part
3 of 4 people
found this instruction helpful.
-
Ted from Harrisonburg, VA
- Easy
- 15 - 30 mins
-
Screw drivers
instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.
Dremel and it works!The instalation part of the "job" was less then 10 min.
Was this helpful?
Thank you for voting!
Ice maker didn't work.
3 of 4 people
found this instruction helpful.
-
Amanda from New Albany, MS
- Easy
- 15 - 30 mins
-
Screw drivers
Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable s
... Read more
hould be more flexible and adapt to the fridge a little more friendly.
Read less
Was this helpful?
Thank you for voting!
Ice maker arm disconnected from frame causing problems.
5 of 10 people
found this instruction helpful.
-
Kenneth from Callaway, FL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker
... Read more
and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.
Read less
Was this helpful?
Thank you for voting!
No water to icemaker.
2 of 2 people
found this instruction helpful.
-
Richard from KANSAS CITY, MO
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Checked water inlet tube inside freezer, stuck screwdriver in it to see if there was any ice and it seemed clear. Checked water pressure to fill valve, good pressure. Replaced fill valve, still no water to ice maker. Replaced Ice Maker. Still no water to Ice Maker. Removed freezer back panel, hit fill tube with heat gun after allowi
... Read more
ng freezer to defrost awhile, replaced back panel, ice maker. Water going to icemaker fine. Problem was that the fill tube was frozen up way at the back where the water line emptys into the icemaker fill tube. Old icemaker and fill valve were probably OK. No real way to check it from outside the case in the rear of the fridge as the water line is sealed on the fill tube and heating it without removing the rear freezer panel does not get back far enough to melt the ice.
Read less
Was this helpful?
Thank you for voting!
Refrigerator wasn’t cooling, but the freezer was.
2 of 2 people
found this instruction helpful.
-
Carl from JAMESBURG, NJ
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Unplugged the fridge.
Took off the freezer door.
Took off the door brackets and the ice machine. Removed the back panel. Unplugging the light and the ice machine were a challenge to get to. Installation of the fan motor was simple. Reverse all the directions, done. Tough part was figuring out what to take off.
Took off the freezer door.
Took off the door brackets and the ice machine. Removed the back panel. Unplugging the light and the ice machine were a challenge to get to. Installation of the fan motor was simple. Reverse all the directions, done. Tough part was figuring out what to take off.
Was this helpful?
Thank you for voting!
Water leaking and freezing everywhere. Weird shaped ice cubes, more like chunks which jambed the dispenser.
3 of 5 people
found this instruction helpful.
-
Peter from Riverdale, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic
... Read more
door jamb putting the new unit in but other than that all is well and functioning well.
Read less
Was this helpful?
Thank you for voting!
both freezer and refigerator were warm.
2 of 2 people
found this instruction helpful.
-
Harry from DURYEA, PA
- Easy
- 15 - 30 mins
-
Nutdriver
I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and
... Read more
tried restarting the unit. Everything went well and it fixed the problem.
Read less
Was this helpful?
Thank you for voting!
Ice maker
2 of 2 people
found this instruction helpful.
-
Eli from Buford, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"
Was this helpful?
Thank you for voting!
The refrigerator and freezer were running hot.
2 of 2 people
found this instruction helpful.
-
Glenn from GLENSIDE, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the onsite video and had no problems. Shut off refrigerator, removed storage trays and bind, removed the rear panel under the light, identified the orange and pink electrical wires and cut them. Spliced the new wires of the thermostat with refrigerator wire and capped them, applied electrical tape to insure no moister makes con
... Read more
tact with wires. Replaced rear panel and storage racks and bind. Plugged in the refrigerator and it is operations like new. I was about to purchase a new refrigerator for $ 1,300.00 and the thermostat costed $ 13.00. What a Christmas present!
Read less
Was this helpful?
Thank you for voting!
Refrigerator ice cube maker stopped making ice cubes
2 of 2 people
found this instruction helpful.
-
JAMES from MATTESON, IL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
I replaced the water line and the inlet water valve
Was this helpful?
Thank you for voting!
Squeky Evaporator Fan
2 of 2 people
found this instruction helpful.
-
Douglas from LAFAYETTE, LA
- Really Easy
- 30 - 60 mins
-
Screw drivers
I made my wife fix it.
Was this helpful?
Thank you for voting!