All Installation Instructions for General Electric Dishwasher GDWT100R00WW

Needed to replace rollers on bottom dishwasher rack

Pulled off old rollers and snapped on new ones. Never easier!

Parts Used:

Dishrack Rollers and Axles - Kit of 8

Marilyn from CALDWELL, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

one old roller broke

pulled off all old rollers and axiies and snapped on new ones

Parts Used:

Dishrack Rollers and Axles - Kit of 8

Barry from FISHKILL, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Replaced dishwasher but had the wrong drain hose.

Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.

Parts Used:

Drain Tube Kit

CLAMP

Victor from Phoenix, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Would not fill with water

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

Parts Used:

Water Inlet Valve

James from JONESBOROUGH, TN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Water leaking underneath dishwasher

went online to parts select. Looked at parts that could be leaking. Thought it was the sump. Purchased the sump and the pump connector. Almost bought the adaptor pump assembly, but it was $29.00. Parts arrived in about 2 days. Turned off water and power to dishwasher. Disconnected the copper water line. Hardest part was getting the dishwasher out of space. Once out, layed it on it's side. Parts held together with clamps. Took it apart like a puzzle. Replaced the parts, tightened the clamps. Pump connector hard to unscrew. Got a good hand grip on it and turned it loose. Sump did have a hole in it. Put everything back together. water, electric, etc. Turned it on and it was leaking. Leak coming from the adaptor pump assembly. Couldn't wait 2 more days.Found part at a local parts store for $40.00. Was able to change it by reaching underneath and not pulling dishwasher out again. All three parts needed to be changed. Dishwasher now working fine. If your leaking underneath and taking out the dishwasher change those 3 parts.

Parts Used:

Sump

Pump Connector

Anthony from East Islip, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Socket set, Wrench set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher would only 'partially' drain; dishes needed more rinsing.

Called repairman: announced that the drain pump was gone. Did not seem right. Went to the website. Found what I was looking for. 49% of the time it was a check-valve issue; only 26% of the time was the pump the problem. Took the unit from under the counter; got it on its side; removed the drain pump. Found my first check-valve, but thediagram showed a second lower one toward the sump. Having located both and purchased two valves and and the lower holder piece, I was ready to finish the job. Quarter-inch nut driver and a screw driver and the valves were in and the drain pump re-installed. Most difficult in my case was getting the dw back into its spot and lashed down! Thanks for the good guidance!

Parts Used:

SEAT CHECK VALVE

Check Valve Flapper

James from SEDONA, AZ
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Wire basket rusting.

The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.

Parts Used:

Upper Dishrack Kit

Complete Lower Service Rack Assembly

Scott from pleasanton, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

ball bearings falling out of the upper dish rack

pulled the end caps, pulled the upper dish rack out. Installed the rear end cap on the right hand side of the inside slider for the rack. installed the bearing and slider in position. Put the upper rack back in and installed the front end caps.

Parts Used:

Cage Roller Bearing Assembly

Upper Rack End Cap

George from Cincinnati, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Original wheels kept falling off, rack would go off track and it drove me crazy

Simple, took five minutes, no tools, problem solved.

Parts Used:

Dishrack Rollers and Axles - Kit of 8

Chris from Medina, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

emit holes partially plugged and metal of lower arm separated

lower arm lifts off and new sets right on. The upper arm needed a "holding" screw removed (from under the shelf) and replaced with the new arm.

Parts Used:

Lower Spray Arm - Gray

Middle Spray Arm

Mary from LARAMIE, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old parts showing wear

Watched a YouTube video on disassembly, parts replacement, and reassembly.

Parts Used:

Fine Filter

Fine Filter Hub Nut

Suzanne from CHEYENNE, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Leak under the appliance

After finding the leak source I have targeted the piece part on your web. It came 2 days after and I replaced the defective part by the new one. I switch off the water, untied the nut to release the pipe, take out the part.

Parts Used:

Adaptor Pump Assembly

paul from arlington, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Bottom dishwasher rack rusted out

Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.

Parts Used:

Complete Lower Service Rack Assembly

John C from SPRINGFIELD, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Older wheels had broken clips.

Simply remove broken wheels and clip on replacements. No tools are necessary for this fix and the replacement was inexpensive and easy to install. The kit worked beautifully.

Parts Used:

Dishrack Rollers and Axles - Kit of 8