Models > GC-L288GSXP > Instructions

GC-L288GSXP (ASTCNA2) LG Refrigerator - Instructions

All Instructions for the GC-L288GSXP
31 - 45 of 62
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dampness on gaskets, mold and mildew
on left side door, I had to remove the flapper (the piece that rotates when you close the door to allow right door to seal. very simple, remove the flapper hingelift up to get the flapper off the door and move it out of the way.
Remove both door gaskets by pulling them out with your hands. Not the orientation of the gaskets because you will have to install the new gaksets in the same orientation.
Press the new gasket in place, into the slot that goes around the inside of the door, by using two fingers to press it into place. Cntinue this all around then go back and press again to assure the gasket is fully seated.
In my case, replacing the gaskets did not solve the issue, but they needed to be replaced do to the condition. The moisture issue was resolve by replacing the flapper (mentioned above)
Parts Used:
Door Gasket - Gray - Left Side Door Gasket - Gray - Right Side
  • Thomas from Wendell, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking
Swapped old one with new one. New one had extra plug not needed.
Parts Used:
Water Inlet Valve Assembly
  • Johnny from MOUNT OLIVE, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The refrigerator ice maker needed replacing
The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.
Parts Used:
Refrigerator Ice Maker Kit Assembly
  • Larry from GODDARD, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My ice maker wouldn't release the ice, nothing was frozen and the motor would just bind
I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!
Parts Used:
Refrigerator Ice Maker Kit Assembly
  • Jodi from WINTER GARDEN, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torn door gasket
Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.
Parts Used:
Door Gasket - Gray - Right Side
  • Tom from BLUFFTON, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
tray was a tight fit but we got it in
work with the tray gently. To ensure this did not break.
Water filter installed was installed exactly the way the instructions stated to be
Parts Used:
TRAY ASSEMBLY, FRESH R Refrigerator Water Filter LT700P
  • Katharine from FAIRFIELD, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Slow water for drinking
Just like on YouTube very easy to do
Parts Used:
Water Inlet Valve Assembly
  • Steven from SEBASTIAN, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice tray was not rotating any longer
Took the old one out and put the new one in.
Parts Used:
Refrigerator Ice Maker Kit Assembly
  • Angela from SAINT JOSEPH, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker and Water dispenser stopped working
Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/
Parts Used:
Water Inlet Valve Assembly
  • Donald from BETHPAGE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Previous glass shelf shattered into a million pieces while cleaning.
Just laid the shelf down. Fit like a glove!
Parts Used:
Glass Shelf
  • Susan from SAFETY HARBOR, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Stopper had snapped off
Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!
Parts Used:
Door Stopper
  • Lawrence from FALL RIVER, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The glass shattered & needed to be replaced
Just popped it in, just as easy as that!
Parts Used:
Glass Shelf
  • David from HAMPTON, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken sliding rails for vegetable and deli tray. Glass replacement for vegetable trays
Removed trays and replaced broken sliding parts and replaced glass
Parts Used:
Glass Shelf Guide Assembly,TV GUIDE ASSEMBLY,RAIL
  • Nancy from COUNCIL BLFS, IA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker not working
Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice
Parts Used:
Ice Maker and Auger Motor Assembly
  • Franck from ST PETE BEACH, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice and water large paddle button stuck so would not turn off
Scary not hard. But pry panel out start at bottom or right side and pull. and was told from tube video that lg said if you break a few tabs that was normal and not to worry there is plenty. I think I broke one but after repair just pushed it back into place and it is good as new. The broken part was obvious and easy to replace. Just go for it
Parts Used:
BUTTON,LEVER
  • Jerry from Wellston, OK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GC-L288GSXP
31 - 45 of 62