Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
pulling the dairy draw out, a plastic knob broke,that keeps the cover on the draw on tight.
2 of 2 peoplefound this instruction helpful.
Daniel from Margate, FL
Easy
15 - 30 mins
Screw drivers
after pulling the draw out. had to remove 3 screws on the left side, pull out one part, and then replaced the broken pin. put everything back in place and it was done.perfect job.saved alot of money. thanks to part-select
Was this helpful?
Thank you for voting!
Lid to pantry broke off.
2 of 2 peoplefound this instruction helpful.
Alexander from Chicago, IL
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
It was very easy. I removed the two crisper drawers and the glass shelf above the pantry section. I removed two bolts with a nut driver and one screw from the slide track. I pulled out the broken piece and did that all in reverse. Took 5 mins tops.
Also I wanted to say I got my replacement part in two days with standard shippi
... Read moreng.
Read less
Was this helpful?
Thank you for voting!
Right Door Magnet weak, door would not stay firmly closed
2 of 2 peoplefound this instruction helpful.
Larry from CHIRENO, TX
Really Easy
Less than 15 mins
Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.
... Read more> "To infinity and beyond."
Read less
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 peoplefound this instruction helpful.
stu from richmond, VA
Easy
Less than 15 mins
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 peoplefound this instruction helpful.
dorotea from staten island, NY
Really Easy
Less than 15 mins
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 peoplefound this instruction helpful.
Thomas from Roseville, CA
Really Easy
Less than 15 mins
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
ICE BUILD UP AT BOTTOM OF FREEZER
3 of 5 peoplefound this instruction helpful.
Gerald from COLORADO SPGS, CO
Really Easy
30 - 60 mins
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this helpful?
Thank you for voting!
Tried to level rear wheel without unloading bottom freezer and broke the long leveling bolt.
2 of 2 peoplefound this instruction helpful.
Robert from BRANCHBURG, NJ
Easy
30 - 60 mins
Socket set
Unloaded refrigerator. Pulled refrigerator from wall. Removed bottom panel on back and replaced bolt. Reversed steps but leveled rear wheel before reloading.
Was this helpful?
Thank you for voting!
Bottom drawer access door hinge pin broke of pantry end cap - right side. The pin(knob) is a molded part of the end cap.
2 of 2 peoplefound this instruction helpful.
Neil from E GRAND RAPID, MI
A Bit Difficult
30 - 60 mins
Nutdriver
Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.
Was this helpful?
Thank you for voting!
I broke the parts while moving
2 of 2 peoplefound this instruction helpful.
terry from BLACK MTN, NC
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Was easier than I thought it would be . Thanks to your diagrams for the parts.
Dropped a jar onto the pantry and broke the plastic piece on end cap that moved the drawer lid.
2 of 2 peoplefound this instruction helpful.
Terry from N SYRACUSE, NY
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm f
... Read morerom old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.
Read less
Was this helpful?
Thank you for voting!
Empty box sent with no part!!!! No customer service help because of covid
2 of 2 peoplefound this instruction helpful.
Jeffery from MIDLOTHIAN, VA
Very Difficult
More than 2 hours
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
My Orders
