My Orders
FWTR445RFS1 Frigidaire Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
originall shock was broken
48 of 60 people
found this instruction helpful.
disconnected the power and water supply.
removed the back panel.
unscrewed the contol board that blocked access to the bottom of the shock absorber.
pulled the original pins out with pliers while pressing in the piece that prevents it from working its way out.
removed the shock absorber.
... Read more r />placed the new shock absorber in the bottom mount, put soap on the pin for lubrication and pushed it through the hole. Put the top of the shock absorber in its place and placed the other pin in.
replaced the control board and replaced the rear panel.
removed the back panel.
unscrewed the contol board that blocked access to the bottom of the shock absorber.
pulled the original pins out with pliers while pressing in the piece that prevents it from working its way out.
removed the shock absorber.
... Read more r />placed the new shock absorber in the bottom mount, put soap on the pin for lubrication and pushed it through the hole. Put the top of the shock absorber in its place and placed the other pin in.
replaced the control board and replaced the rear panel.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
motor burned out, tub quit going around
52 of 72 people
found this instruction helpful.
First I turned off the water and disconnected the hoses. I took off the back panel and unscrewed the 4 bolts holding the motor in place. The grounding screw was impossible to remove, so I had to cut the wire off. Took out motor and disconnected the electrical connector. Put new motor in (ordered new belt, figuring it would need replac
... Read more
ing - was still in excellent shape, but replaced it anyway), bolted in the motor (socket set works best on further away bolts, screwdriver for closer ones). Put the belt on the motor first and then pulled it up over the side of the tub and turned the tub to get it around the whole tub - took alittle bit of turning to get it on. Plugged in electrical connector and screwed grounding wire into hole. Replaced back panel and water hoses. Got a bit dirty and sweaty but not too hard to do it yourself, as I am a 48 yr woman and don't usually do this kind of thing.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Rear tube brackets broke, made a banging sound in final spin
37 of 46 people
found this instruction helpful.
My repair went well except I removed the rubber seal between the tube shell and front door, BIG MISTAKE! Next time I will leave the front half of the tube shell in tack in the washer and just remove the rear half of the shell. If it wasn't for having to reinstall the rubber seal between the tube shell and the front door, the whole proje
... Read more
ct could have been down in under two hours.
Food for thought next time! :-)
Food for thought next time! :-)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
washing tub had broken away fm 3 of 4 supports
34 of 38 people
found this instruction helpful.
disconnected fm water supply and electrical ckt
move washer fm beneath dryer (stacking config.)
removed back, found 2 broken shocks (round type) and 1 broken spring (left looking from back). checked online for parts and found your site. ordered and waited a few days.
back on task, removed controls (lower left cor ... Read more ner) to reach pins, removed front lower panel, removed pins and broken remains of both shocks. removed broken spring. left remaining spring to keep tub suspended.
back on task when parts arrived. installed shocks --note that it was not clear that there are 2 shocks in each package (so i order 2 pkgs and now have 2 extra shocks --for next time it breaks away ;-)
crafted a 'hanger' with 10ga wire and 2x4 to permit tub to be supported and/or suspended without unduly stressing new components. attached both shocks being careful to follow instructions about alternating direction and orientation in relation to plastic bushing on the shock mounting points. removed remaining spring and used short length of 10ga wire to pull spring into position and lock.
re-assembled back and front cover... re-attached control circuit. moved closer to water and electrical supply and tested through 2 cycles --no problems found.
put back into position and leveled and locked.
works fine now.
move washer fm beneath dryer (stacking config.)
removed back, found 2 broken shocks (round type) and 1 broken spring (left looking from back). checked online for parts and found your site. ordered and waited a few days.
back on task, removed controls (lower left cor ... Read more ner) to reach pins, removed front lower panel, removed pins and broken remains of both shocks. removed broken spring. left remaining spring to keep tub suspended.
back on task when parts arrived. installed shocks --note that it was not clear that there are 2 shocks in each package (so i order 2 pkgs and now have 2 extra shocks --for next time it breaks away ;-)
crafted a 'hanger' with 10ga wire and 2x4 to permit tub to be supported and/or suspended without unduly stressing new components. attached both shocks being careful to follow instructions about alternating direction and orientation in relation to plastic bushing on the shock mounting points. removed remaining spring and used short length of 10ga wire to pull spring into position and lock.
re-assembled back and front cover... re-attached control circuit. moved closer to water and electrical supply and tested through 2 cycles --no problems found.
put back into position and leveled and locked.
works fine now.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Spider was corroded and broke from being weakened by the corrosion
33 of 41 people
found this instruction helpful.
Removed the entire front cover of the washing machine and dicoonected the springs that support the tub. Left the tub down and disconnected the struts and unhooked all the wiring and pulled complete tub out of machine. Removed all the bolts around the tub shell and split the tub shell. Remover the motor from the sheel to make it lighter to
... Read more
work on, removed the pulley on the drum shaft and pulled the drum out of the shell. Found that the cast alluminum spider was weakened by corrosion and this caused the spider to break. The spider itself should be able to be purchased seperately because the stainless steel drum was okay and could have been reused. The biggets problem I had was getting the tub back in the washing machine and getting it suspended by the springs again. I used a 6 x6 block and a 2 x 6 board to lift the tub up in the air to get the tub springs hooked back up. This took 2 people to accomplished. After the tub was suspended on the springs the rest was easy.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!