FWT449GFS2 Frigidaire Washer - Instructions

First thought the problem was with the spin cycle, however it soon became clear it was the pump that wasn't draining the water that kept the spin cycle from doing it's thing. After hand-wringing a large load and shopvacing out the remaining water, I ordered the new pump, got it in two days, and did a quick change out and it works perfectl ... Read more y. During the removal of the rubber boot that connects the tub to the pump, the one thing I did discover was a yucky buildup of years of fabric softener which I couldn't break my wife from using. But, after showing, and more importantly, letting her SMELL the fungus/mildew in the sludge, I've finally broken her of the habit! Best bang for the repair buck so far.

Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no ma ... Read more tter what else you fix, this will break and kill it at some point. Piece of crap!

first took off old pump off by removing 2 screws and removed 2drain hoses under front load washer with pair of pliers then put new pump on same as removal.

2 screws and about 48 seconds of work. very easy.

door not level son slammed shut and door strike broke

Very simple! Found the part using the diagrams and photographs on this site. When it came, my husband ust pulled the remainder of the broken knob off the little post with a pair of needle-nosed pliers. Slid the new knob on. It took longer to find the pliers than to make the repair!

Had to replace one Spring on top of the tub and both shock absorbers. Anyone with even a limited amount of mechanical ability could handle this repair. Save yourself about $300 in repair cost and replace these items yourself. Spring and Shocks absorber kit cost less than $60 with shipping.

Just look at the diagram that comes wi ... Read more th the parts, it's a piece of cake. The most difficult part is replacing the spring, she is stiff. You will need to take the top of the machine off, which is super easy, and remove the metal keeper on top of the frame rail. Get someone to help you as you will need to lift the tub and slip the spring over the frame rail.

The shocks are the easiest part of the repair, and should take less than five mins. to replace.

disconnected electric and water supply. removed back cover from front loading washer. removed two screws from spring end plate on the top of the washer. replaced old spring with new spring/insulators by lifting the tub and hooking the new spring on. replaced the back cover and top spring cover plate. reconnected water supply and electri ... Read more c. machine is working like it did before the spring broke. very easy fix. the majority of the effort was moving the washer around to get easy access.

E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.

First I removed the "wire" and spring that hold in the rubber seal at the door.

Then I removed the 2 screws that hold the door loc ... Read more k in place.

Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.

Runs fine now.

I was hoping it was the drain hose but it wasn't. It's a front load washer so I pulled the kick plate in the front (2 screws) removed the three clamps and put the new hose on. Easy job, saved a hundred or so from the repair man. Part cost 35 bucks!

First I went on-line and found a download for the parts catalogue which contains a schematic for the washer. After looking this over I could determine how to get the washer apart! After getting the front panel off, I disconnected the drain hose from the pump with a pair of water-pump pliers. As I pulled this hose out, water spilled out ... Read more all over the floor, so I then cleaned that up. Next I connected the new hose and put the machine back together. This job would have cost me over $150 if I had called in a repairman. PartSelect saved me so much money, and I thank them so much!

The tub is supported by two springs and two shock absorbers. First remove the back panel of the washer. Then I placed the auto jack from my car under the tub, alongside the motor, and cranked it up, lifting the tub, until the top of the seal in the front was compressed. Then I took the top off of the washer to access the springs. There ... Read more are retaining straps over the top of each spring that I had to remove to get to the springs. Pulling up hard on the spring allowed me to get a pair of pliers on the spring and pull it out of the slot it was in.

Once it was out of the slot I could remove it from the tub as well. I put the new spring in and replaced the retaining strap. Then I repeated this process on the other spring.

Once both springs were in place the tub was hanging as it should and the seal around the door was smooth all the way around. I haven't seen any more leaks since replacing the springs.

This is a newer washer, but I don't know the age. I just bought the house...!

I made this repair more difficult than it needed to be. I took off the back panel of the machine completely, only to discover the coupling for the hose was near the front of the machine. I tilted the unit on its side and took off the bottom before ... Read more I discovered the access panel on the front, which is held on by only two screws. I put the bottom panel back on, tilted it upright, took off the panel, and had easy access to the coupling. The new part fit perfectly, and a quick wash load proved the leak was fixed.

1. replaced (2) shocks, remove bottom cover 2. (1) spring and rib belt, used a wooden block to hold up drum , rolled out ld belt and rolled in new----remove top and rear covers after replaced same ---thanks..

Pulled washer electrical plug from receptacle.
Unscrewed hot and cold water inlet hose connectors.
Removed screws retaining backplate.
Removed back plate.
Removed two screws connecting valve assembly to frame.
Pulled two spade electrical wire connectors from valve assembly.
Opened hose clip securing hose on o ... Read more utlet side of valve assembly, using pliers.
Pulled hose from valve assembly.
Valve assembly now free.
Reversed above with replacement valve assembly.