FFEF3043LSK Frigidaire Range - Instructions

Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center porti ... Read more on was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.

My husband removed the old one in a few minutes, the just popped the new one in when it came. Not for nothing, (where we purchased the stove) wanted $67 for the same part you all charged $49.00

Slide out the old; slide in the new!

I tested incoming and outgoing voltage at the timer! The timer showed to be defected!

Replaced the dual element switch and that fixed it up

1. turn off power to stove and pull out from wall. 2. Remove 4 screws holding rear upper panel in place, pull panel up and out to remove. 3. Remove 4 screws holding clock timer to back of raised panel. Let it dangle from attached wires. Gently peel overlay from face of old timer(if reusing). or peel off adhesive backing from new overlay a ... Read more nd apply to face new clock timer. 4. Attach new timer to back of stove raised panel where the old one was, using the 4 screws originally removed. 5. remove each wire one at a time from old clock timer and plug into the corresponding terminal on the new one. (careful they are tight). 6. Set upper rear panel in place and fasten using the 4 screws originally removed. 7. Slide stove into place and restore power. 8. Reward yourself with fresh baked cookies!

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minu ... Read more tes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Self easy

PS Great service Super FAST.
Thanks Jesse

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connec ... Read more t them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a ... Read more and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

My husband followed the video instructions and it was easy to fix.

Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed n ... Read more ew ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!

Twisted replacement bulb into place easily. Let there be light!

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. P ... Read more retty simple job though.