FFBD2406NW9B Frigidaire Dishwasher - Instructions

Took me about 2 minutes to repair, no tools to repair, very easy installation repair!

Pulled the old one off and pressed the new one on (plastic clips hold it on). Dishes much cleaner now.

Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

Replacing the part was easy. Just pop the old one out and pop the new one in. This item fixed my leaking door problem. The old arm had fallen against the heating element, which burned a hole through the end. Water was shooting out that hole and leaking under the bottom door seal. Replacing the door seal did not help, but replacing th ... Read more e arm fixed the leak.

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I a ... Read more sked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

The original lower spray arm had one end break loose the metal retainer end. I used a temporary small hose clamp to fix as I waited for the new lower arm to arrive.

The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.

I removed the bottom drawer and glass trap in order to remove the old melted down washer arm. Once those parts were removed I was able to easily secure the new replacement be ensuring that it was turned enough and fit down securely (side note, if you don't hear the arm click or snap into place, it isn't secure). The part works just fine, ... Read more but sadly I think I have another problem with my washer, but I will figure it out.

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

So purchased new arm, trap and lower arm support and put in together correctly. Easy peasy all the parts snapped in place using no tools. I'm a 70 yr old gramma and no problem. Just wish I put it back together correctly the first time and saved myself the money. Never know what you can do until you try. Parts came super fast too.

The part wasn't correct and I have to pay postage back which is nearly as much as the part so it's stupid for me to spend more money on a part that want work I want order from your store again.

Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.

Eventually broke off old heating element to get it out

It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off ... Read more so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!