FFBD2406NW9B Frigidaire Dishwasher - Instructions

My husband and dad actually did the repair, but my husband not being a handy guy said it was, 'so easy, anyone could do it!' He was very nervous about taking on the project, the longest part was testing to make sure it worked(running a cycle).
The simply pulled out the dishwasher, after disconnecting all electrical power, drained the ... Read more rest of the water that we couldn't see from above, following the video given took out the old part without needing to take out the motor and were able to replace the drain pump, put everything back together besides sliding it into place in case it didn't work, in less than 15 minutes! When the short cycle finished and the water had drained they put it back into place and ran an energy saver cycle and it worked like a charm! Since then(2 weeks ago) we have now ran every function and have had no issues! Every time we open the dishwasher we comment on how much we missed having a dishwasher! Haha!

Most of the time is spent cleaning out under the sink, turning off water valves, disconnecting hoses and collecting water. One valve did leak when closed. Then pull out the dishwasher from under the counter, unplug and lay flat on floor.
Disconnect power from pump. Remove 2 screws and bracket that holds pump in place, gentle twist a ... Read more nd pull out pump. Place tow gaskets around pump. Wet gaskets and gently push pump in place be sure to line it up so bracket goes back in place. Tighten screws, put hoses back in place, push dishwasher back, connect hoses, open valves, check for leaks then run the dishwasher and check operation of pump. I recommend viewing replacement on part select youtube video to determine if you can make the repair.

1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!

VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.

I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely ... Read more recommend this site to anyone, and would use it again. Five Stars!!!!

Unscrewed the housing for the old piece and screwed on the new part. No tools needed. Easy to use website, fast delivery. Very easy.

Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.

My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!

It was super simple. I popped the clips that were holding the old spray arm on and then popped the new one in place.

Replaced upper wash blade and used screwdriver to pop off rail stops to slide rack all the way out to exchange

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

I read the instructions that others had posted and completed the repair in less than 5 minutes!

After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory ... Read more this way.

I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.

Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video s ... Read more howed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

My brother in law installed it for me. There was some difficulty finding the right angle but once we realized we needed to start at the very right side it went well. So far no more leaks.