FAFW3801LW3 Frigidaire Washer - Instructions

Removed two screws and replaced the door strike.

Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clamps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.

Very simple, unplug washer for safety, remove 2 Phillips screws form bottom of front panel, slide panel down to slip the ears out of their slots. set panel off to side, remove the electrical plug on the pump, unscrew the two hold down Phillips screws, raise the pump up and slid a heavy absorbent towel under the pump, loosen the two clamps, slide the hoses off, remove the sloppy wet towel, install the new pump, and screw it down, push the electrical connection on, slip the hoses on , clamp them in place, install the front cover by aligning the slot and ears up, use a screw driver or something the raise the panel up in place then install the last 2 screws plug it in your done.

I took off the top of the washer. It seemed easier than playing with the door gasket. It took about 15 minutes. Everything worked great. The washer is working again. THANKS PARTSELECT

Remove the broken striker, screwed in the new one in less than 2 minutes...this is the second time it was replaced...the first time I was still under warranty...he took about the same amount of time to install ...I ordered 2, because I know it will be broken again....

It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.

Removed the door lock and switch assembly. With needle nose pliers, I removed the metal ring around the washer gasket. Removed two screws on assembly and removed the entire assembly. Noted part number and ordered part which came in 3 days. Reversed the above instuctions for removing the assembly. Was washing within the hour. By the way, I am a 65 year old woman.

Remove Door and front panel, breakdown door and remove front panel. Reassemble door using new front panel and install door strike and bottom screw on door. align hinge with tabs on hinge assembly and insert tabs on front panel and squeeze door parts together and install rest of screws. Job complete

Unscrew 2 screws. Replace part by screwing the 2 screws back in place. Parts received in 2days part replace less than a minute

Our washer is in a very tight spot, and we use the top for storage, so it was a job moving everything and pulling the washer away from the wall. Unplugged, then took the 2 screws off the back, dropped one and retreived it with masking tape on a dowel. Got the top to slide back, then took the screws off the latch. Crammed my arm down inside (very tight) and grabbed the latch, pulling it out the top. Labeled both sides of the connections with colored masking tape (in case we need to replace this part again, but I hope not). Got everything back together, then put the top back on, dropping the same scew behind, retreived it,plugged the power in and it works!!

Remove the seal ring underneath the front gasket.it's solid wire ring held together with wire spring.I used a screw driver to stretch wire ring from gasket.pulled gasket back from washer opening, near striker. removed two screws on striker lock assembly.pulled it out.removed all three wire attached to assembly.plugged in new assembly.replaced screws. reattached gasket and ring. done.

In order to get to the switch located on the right front behind the from panel the top had to be removed with 2 screws holding it in place on the back of the machine. Next the top front control panel needed to be removed by first removing the detergent drawer on the top left of the washer. There are 3 screws that need to be removed behind the slide out dispenser. ALS there are 2screws on the top left and right that need to be removed.. Once these are all removed you can slip the control panel up and over the top and let it rest there. I might suggest that you should unplug the machine from the electrical outlet. Once this is all done there are 4 screws holding the bottom of the front panel that must be removed. If you have pedestals on your machine you can pull the drawer out to get to them. If not you will need tp tilt the machine back and using a block let it rest on it to get to them. Once these are removed you will need to remove the block and set the washer back on its feet. There are now 2 screws at the top to be removed. Once removed lift and pull out the front panel. Set aside. You are now ready to remove the front rubber boot from the washer.. There is a spring that is behind the front rubber that needs to be removed. Using a screwdriver, at the bottom of the front boot you will see the springs once you peel a bit of the rubber back. Remove the spring and set aside.. Now you are ready to remove the door lock switch. Using a Phillips screwdriver remove the screws from the front panel and push the switch back toward the rear. It should pop out very easy. Unplug the switch from the harness and replace with a new switch.. Put the machine back together in the reverse order. Hope this helps.

Took the back off and installed the belt tight but ezsy to do