ER8GHKXMS00 Whirlpool Refrigerator - Instructions

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot

I placed the glass into the frame. I attempted to slide the frame into the refrigerator over the two crisper drawers. It wouldn't go.

My son came to my rescue. "Mother, the drawers slide into the frame". He took the drawers out, put the frame in the refrigerator, placed the glass cover into the frame, then slide the drawers back into the rungs made for them in the frame. Easy peasy! ;

Ordering was made smooth with a good program for finding parts.

Thank you.

Removed door and replaced bushing bracket was ok.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Like you video

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

When you plug in the fridge it will begin to make noise, but never get cool. When you open the door it will stop and will not turn back on.

This part is listed as one that can fix the problem, but the installation video does not match my fridge.

I've replaced the capacitor (PS11757023), the compressor start relay (PS11740412), and condenser fan (PS1957416) and none of them have fixed the problem.

I really don't want to throw this fridge out. Please help! justin@jplt.com

Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut off valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!

Don not completely remove holding icemaker screws. Unit slips over screws and drops down into place and the use nutdriver to tighten in place. Rest of unit was sound and wasn’t replaced.
After icemaker is installed wait for a while and unit self activated and creates ice cubes.

I watched the video that was included with my on line order, it was helpful, although different model shown . I would say it was not difficult to install, the enclosed instructions were a bit confusing.

shook bottle and painted waited a day and repeated