EB2SHKXVD02 Whirlpool Refrigerator - Instructions

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

I searched the internet for the correct part and reviewed the instructions on the internet. Upon ordering the correct part I was provided a link to a video that walked me through step by step. The very first thing I did was unplug the refrigerator.I then located the control board located in the housing in the ceiling of the refrigerator. Using a screwdriver I was able to carefully separate the housing from the refrigerator ceiling . Unplugged the housing and then had to separate the plastic housing to locate the control board. Ran into a little difficulty at first separating the plastic tabs but with a screwdriver carefully pried the tabs. Once completely open is where the control board was. More plastic tabs holding the control board in place. Carefully separated the board from the tabs. The were two plugs that needed to be separated from the board. Used a screwdriver to get the plugs separated.The new board you had to bend carefully at a joint so the board became two pieces. Snapped the boards in place. Plugged the board in two spots. Put the housing together and put the housing in place in the refrigerator. Plugged the refrigerator in. All lights came on and then had to program the board. The instructions were spit on. The code is located inside the fridge were the model tag is. Programmed correctly. Word of advice read the directions a few times you can't go wrong. So far it's day 7 after I installed the board and no ice building up. According to the internet the control board controls the defrost function on my model. Very happy. I'm still watching the freezer but I'm pretty sure I fixed my matter. Thanks for sending the right part and the video. Repair went well. Just take your time and go easy because everything involved is plastic. I didn't want to break any tabs I had to deal with.

Followed the video and installed the new Jazz board. The board cam in 1 piece which had to be separated into two pieces, but the scored area on the board made it less intimidating. At the same time I replaced the two incandescent lamps in the refrigerator area with LED lamps. Getting the housing for the control board apart was the most difficult part, installing the replacement board was a breeze.

Unlug refrig or turn off refrig from its control panel On/OFF switch.
For ease of work remove freezer shelve directly below the ice maker. Remove four screws from the bottom of the ice maker assembly, three that secure the ice maker and the other that holds a plastice shroud in place over the ice maker's power plug.
The ice maker is now ready to be removed; it will slide forward by pushing up on left and right side of the ice maker's mounting slide rails. Once the ice maker is moved forward it is easier to disconnect its power plug (depress a locking tab on the side of the connector and pull connector apart and remove ice maker assembly.
Remove and replace motor module by removing three screws and and replace with new unit.
Reverse ice maker removal proceure for installation. Once installation is completed turn on Power to Refrig, Ice making should begin after a few hours.

Just snapped in new shelf

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

went on this website to fine info ALWAYS GO TO TYE OF APP. FIRST THEN TYPE IN MODEL NUMBER...THAT WAY YOUR GOING TO GET THE INFO ONLY TO YOUR APP. then search under symptom .." DO LOTS OF READING HERE ",CLICK ON COSTUMER REPAIRS thats were i found additional info on my problem..now on to the fix.. it stands to reason that on my appy. anyways that if the to parts plug into each other then you should think smart and get both avoid the coming "i told you so, you should have ordered the other part to" didnt cost that much extra... word of advice here .. i have big hands so when " they say" to plug both together then plug into the compressor...DONT!!!! plug the start device in first then plug in capacitor... almost forgot!!!! make sure ALL ELECTRICAL PLUGS AND WIRES ARE CLEAN-NOT BURNT ECT... used a can of electric contact cleaner-NOT ON THE NEW PARTS JUST THE COMPRESSOR AND THE WIRE THAT PLUGS INTO THE CAPAC. .. its just that simple... you will have to let the app. run for at least 24-36 hrs. to get cool enough and stabilize. after that we had to readjust the temp settings a little bit no bigee enjoy!!!!!

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.