DWD1500AWB Admiral Dishwasher - Instructions

Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer

Snapped the old part out and snapped the new part in.
It was a piece of cake.

First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!

I removed the washer from under cabinet.Turn unit on its side,removed hose connection,removed mounting screws,disconnect wire plug and removed drain pump.
I put a small amount of sealant on pump where it contacts the tub and reversed the process. Parts received in record time and in great shape.

I removed screws in trim, kick panel and counter top. Turned off breaker at electric box, Dishwasher slid out easily. diconnected water line; so i could slide entire unit out of cabinet. Laid unit on side and cleaned up the water that leaked out.
Removed the pump with nutdriver, replaced pump and reconnected electric, drain hose and ... Read more screws.
Replaced unit into cabinet, connected water and turned on electric. no leaks, ran machine in rinse cycle, at time for pump I could hear and feel it was running, but no water. Evidently my original problem was the "air gap" device. I repaced it $4 at Home Depot and it works like a champ.
In hind site, the air gap probably ruined the old pump, so you might want to consider changing it out whenever you change the pump.

Impeller bolts to plastic chopper mount which is screwed to the top of the motor. Threads on chopper mount were stripped causing impeller to not spin fast enough (replacement mount, which is part of the chopper kit, is metal). Installtion was not difficult.
You have to reach underneath the washer and wedge a screwdriver on top of th ... Read more e motor to hold the shaft from moving.

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumul ... Read more ator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

You just remove the old unit and set in the new unit. the wheels were already connected.

Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.

Very easy after watching the video. thanks

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

First I shut off the water and electricity to the dishwasher. I removed the screws holding it in the cabinet and pulled the dishwasher out. Disconnect the water line and turn the unit face down on the floor. I disconnected the wire harness by pulling it out. It was a little hard to pull out. Then I removed the screws holding the pump in ... Read more place, then removed the pump. I inserted the new pump and replaced the screws, and the wire harness. Then stand the unit upright, reconnect the water line (use teflon tape to prevent water leakage), put the dishwasher back in the cabinet, and restore power and water. Then you're done. It would have been very simple if I had used teflon tape the first time. I had a leak the first time I reconnected the unit and had to take it out again and apply the teflon tape. After that, everything was fine. The dishwasher works great.

PartSelect web-page for this model listed the handle as the most often ordered part. It arrived the next day after the order. It was necessary to remove about a dozen Torx screws to remove the back from the door. The power was turned off at the breaker. Two electrical fittings were removed from the broken handle and placed on the new ... Read more one, and the part was put into position and the door back screws reinserted. I was fortunate to have the appropriate Torx driver and suggest that PartSelect offer such an unusual tool with the part.

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around lit ... Read more tle knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.