DP476 Jenn-Air Dishwasher - Instructions

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

First I was amazed that the belt was available for my ancient dishwasher. Then I was amazed again when it came overnight. The instructions said to stretch it over the two pulleys but my hands weren't strong enough. In a sudden flash of brilliance I decided to use a screwdriver as a lever to force it onto the second pulley. Done deal - happy home handyman.

Purchased and installed new faucet attachment. It arrived quickly and very easy to attach. Thank you !

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

No tools were needed. The top rack was slid out as far as it could go (no need to remove from the dishwasher) and the utensil basket was removed. Matching the positioning of the other good clips on the upper rack, the new accessory rack pivot clips were snapped into place. The pins on each end of the accessory racks were placed into the pivot holes provided on the clips and pressed into placed. The bottom prong on each clip was then gently pressed upward until it snapped into the groove on the bottom of the clip. The pivot action of each rack was tested. The untensil basket was put back into place and the upper rack was slid back into the dishwasher. Done!

I was not able to follow the instructions exactly since they called for stretching the belt around the back pulley with the left hand. For a woman that prooved too difficult so instead I attached the belt to the back pulley first and used 2 screw drivers (they are thin) to stretch the belt around the front pulley. It took considerable effort but I got it on!! The dishwasher now works. Praise God!!

First, let me say that the parts arrived really fast,--thnaks for the great service!

First I removed the screws inside the door edges. This releases the front door panels allowing access to the detergent cup parts. Then I removed the old cam return spring, the old cam (and the old spring underneath the cam) and the old bi-metal switch. The instructions were pretty clear on how to install the new style return spring and new cam. Then I installed the new bi-metal switch.

Really, the hardest part of the whole repair is getting the door panels back in the proper place so that the screw holes are aligned. That probably took longer than the rest of the repair job.

The new parts have the detergent cup working like new again. Very satisfying repair!

Clip the plastic on to the vertical pieces. No tools needed

followed the scematic on the wesbite that i used to i.d. the repair part needed. removed the front door outside cover (8 screws) removed the bi-metal switch (2 screws), did not need to replace the door latch or spring. replaced the switch and the front door cover and ran the dishwasher to test the new switch. worked fine and has been working fine.

Removed two panels on front bottom to gain access to motor and pump pulley.
Looped belt around motor pulley and partially looped belt on larger pump pulley then turned pump pulley together with the belt until belt was fully installed., then coated belt with silicone grease to lubricate it.. very simple procedure.

One note of precaution, UNPLUG power plug before working on appliance.

It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

Typically when the detergent is not being despensed during the wash cycle, the bi-metal switch is bad (they don't tend to last forever). I took the 4 lower screws out from the inside of the dishwasher door,, unscrewed the bi-metal switch, and screwed in the new switch. I also decided to replace the metal spring for the dish as well, which took the majority of the time. Once you get the idea of how that spring is wound in there, the install goes pretty quickly.

No problem at all. Belt slipped on very easily. Followed directions in the package.

Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.