Models > DP476 > Instructions

DP476 Jenn-Air Dishwasher - Instructions

All Instructions for the DP476
76 - 90 of 90
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No faucet adapter
I unsrew the faucet head, and attached th e adapter
Parts Used:
Dishwasher Faucet Adapter
  • Michael from Irons, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
stretched door springs
Locked door closed, removed lower access panels with 5/16" nut driver, removed old springs with needle nose pliers, put plastic piece on top curved end of spring and placed on slot in door bracket as shown on instructions with part. Did same thing for the other door spring, used the screw driver to stretch the springs down to the first hole in on the base of the dishwasher on each side. Replace the panels. Job done!
Parts Used:
Door Spring Kit
  • Robert B from Frederick, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The Faucet Adapter was worn out.
Ordered a new Faucet Adapter! Simple
Parts Used:
Dishwasher Faucet Adapter
  • Becky from Stanley, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
door spring broken
once i got it out the spring was a breeze
Parts Used:
Door Spring Kit
  • Richard from Silver Spring, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
A gift portable dishwasher did not have the faucet adapter.
Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.
Parts Used:
Dishwasher Faucet Adapter
  • Norm from Hamilton Square, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Space too small to see just where to place belt - Plus the belt had to be put on at the bottom of the dishwasher.
My husband and I both tried to get belt around the pulleys according to directions that came with the belt. The space was just too small to work in. We ended up turning the dishwasher upside down! We could then see what we were doing....My husband finally got the belt on....He did end up with lots of small cuts of his hands from sharp edges. But we were so happy to get it fixed. We had priced new portables dishwashers at six and seven hundred dollars. We were thankful to be able to get the part for our 23 year old dishwasher. It is now working great.
Parts Used:
Clear Belt
  • Shirley from Brewer, ME
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Belt to stiff to roll onto pulley
150 degrees for ten minutes provided enough flexibility to allow the belt to be rolled around the pulley. The machine has been used successfully since installation.
Parts Used:
Clear Belt
  • John from Los Alamos, NM
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
would not drain
The part was a bit difficult to put on and then I discovered that it still would not drain. It turned out that my drain hose was plugged
Parts Used:
Clear Belt
  • Donald from Lake City, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Motor running but no motion or pumping action
Removed the kick plates to access the pulley system, Heated the clear belt in hot water and installed it by rotating the large pulley to stretch the belt on. Then added the lubricant to the belt. Reinstalled the kick plates with nut driver.
Parts Used:
Clear Belt
  • John from Slidell, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broken Belt
After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.
Parts Used:
Clear Belt
  • WILLIAM from CONNEAUT, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
changed out kitchen sink faucet set
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Parts Used:
Dishwasher Faucet Adapter
  • George from Cameron, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would pump the used water out.
Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.
Parts Used:
Float Switch
  • Robert from Bandon, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
leaking water
replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.
Parts Used:
Door Gasket - gray
  • Noel from Temperance, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the pump was not working so the dish washer would not drain
Removed the front covers on the bottom of the dish washer. I found it extremely difficult to stretch the belt over the second pulley so I soaked the belt in hot water for a few minutes to soften it. After I soaked the belt it stretched enough for me to work it into both pulleys. Don't forget to apply the grease (supplied with the belt) after the belt is installed.
Parts Used:
Clear Belt
  • Wendy from West Terre Haute, IN
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The door spring broke in half on the front door of a twenty two year old Maytag dishwasher
Easy repair, I put small marks under the counter to make sure the dishwasher went back in the same spot for easy screwing back in
Parts Used:
Door Spring Kit Door Spring Kit
  • Robert from Leominster, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DP476
76 - 90 of 90
Back to Top