DE22CT Maytag Dryer - Instructions

First, it is IMPERATIVE that the dryer is unplugged from the wall or the appropriate breaker is turned off to prevent electrocution!!! The front of the dryer is removed by removing the two screws at the bottom of the front with a Phillips head screwdriver. Next, remove the door wiring from the wiring clamp and set front / door of dryer ... Read more to the side. Next, remove the bulk head by removing four nuts from the sides with the appropriate nutdriver. The drum belt will have to be disconnected from the motor pulley by lifting the spring of the pulley to release belt tension. This can be done from the front or back access panel of the dryer. The back access panel gives you a better view of the motor pulley and attached belt. After removal of the belt from the motor pulley, the drum of the dryer can be removed. Next, remove the heat shield at the front of the dryer. It is held on with two nuts and can be removed using the appropriate nut driver. Next, remove the blower wheel housing cover using the appropriate nut driver. The blower wheel will be next. It can be removed by using a pair of pliers to remove the circular clamp. A pair of snap-ring pliers will also be need to remove the snap-ring also holding the wheel in place on the motor axle. After the blower wheel is removed from its housing, the housing will need to be removed. The housing is again held in place by several nuts and the appropriate nut driver will be needed to remove them. Next, take all wiring loose from the motor. It would be a good idea to photograph or note how and what wires were attached in specific locations on the wiring harness. The new motor may be different when it comes to wiring and will be accompanied by a wiring diagram and the needed connection ends for the wiring. If it is a different wiring layout, as was my motor that I ordered from this site, a set of wiring strippers / pliers will be needed to cut, strip, and crimp the new connectors. After wiring has been removed from the motor, remove the motor by removing two nuts with the appropriate nut driver from the bottom of the motor mount. The motor, mount, and pulley will then all come out as one piece. The motor will then need to be removed from the mount. This can be accomplished by using a flat head screwdriver and a hammer. Place the flat end of the screwdriver into the raised edge of the motor mount clamp and pull away from the locking bracket. If needed, use a hammer to give that extra tap to the end of the screwdriver to remove the clamps. After the motor is removed from the mount, an Allen wrench will need to be utilized to take the belt glide / seat off of the motor axle. You will also need the snap-ring pliers again to remove a snap ring from this axle as well. Clean the motor mount and dry thoroughly. Grease the pulley housing where it contacts the motor mount for smooth gliding against the mount. It is important that you use a NON-FLAMMABLE grease. This is the end of the "tear-down" phase. Now is a good time to vaccum and clean the inside of the dryer cabinet. This will help insure that excess lint and fuzz is removed to prevent an accidental dyer fire. Next, place the new motor back into the motor mount in reverse order. Make sure the belt glide / seat from the motor axle aligns with the belt marks on the pulley. Reassemble the dryer in reverse order, making sure to follow the wiring diagram provided with your new motor. Also you need to insure that the motor is turned at a 45 degree angle to allow the dryer drum to pass the motor without striking it. After reassembly, plug in the dryer and attempt to start. If your dryer does not start, troubleshoot the wiring first. Wiring was the most difficult part of this repair and working in the tight space provided was a trick. Also look up a video of the repair! This helped me tremendously. Videos can be found on this site or at YouTube.com.

Removed front cover.removed 4 screws holding drum in place. Cleaned out lint from everywhere. Placed new belt over drum looping it over idler arm & motor pulley. Pushed drum back ; rotated drum to see that belt was engaged. Put front drum bracket in place. Put front panel in place with 2 screws at the bottom. Tested motor & rotation of dr ... Read more um; then checked heat. All worked fine. Took 1 hr. but most time spent cleaning lint.

By watching a video I disassembled the front and took the dryer tub out and replace the two rollers and it took about 60 minute.

I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun insid ... Read more e the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.

After viewing repair video I used those instructions, after removing drum place new belt on drum, I used scotch tape to hold belt in place, tape belt with 2 inch strip about every foot around drum, leave extra belt that connects to drive motor folded down and taped to drum. After installing drum connect belt to drive motor and roll drum t ... Read more o remove tape. This will keep belt from sliding out of place on drum while installing.

Removed front panel and tumbler, replaced roller axle,
wheel, and front glides. Anybody can do this.

Fallowed instructions on YouTube

Opened your replacement part and found a broken fin on the blower wheel. no way I was going to return it and wait another week for another part. Perhaps you folks need to inspect what you send out. 1 blower wheel with a broken fin and 2 clamps. Replacement was easy and quickly accomplished. Having replaced drum rollers and the belt this d ... Read more ryer is almost new. Thanks

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find whe ... Read more re they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

I happened to come across a repair story posted by Wayne From Minneapolis MN about how he reinstalled the tumbler, plugged the dryer in, and started it up but forgot the belt and realized that it was the blower wheel that was loose on the shaft. As soon as I read that, I said, "Yes! that's it!" So I ordered the blower wheel and a belt. ... Read more I decided to replace the belt since I saw it was slightly frayed. After all, the dryer is almost 20 years old!

First, switched off the power to the dryer or disconnect it from the outlet. Took the front panel off by removing the two screws near the bottom of the dryer. Pulled the bottom of the panel out and the two clips on the top just disengaged easily. Be careful, there are two wires connected to this panel. Just rotated it to the left and let it rest vertically. If need be, the two wires can be removed easily.

Next, I removed the four screws to take out the front tumbler and the tumbler. Set them aside. Then I removed the belt. You might want to pay attention as to how the belt goes around the motor pulley and the idler pulley before removing the belt.

After nearly 20 years, I'm surprised that it wasn't full of lint and dust. Gave it a good vacuuming and clean up.

Next, I removed the blower cover, the retaining ring, the hub clip, and the blower wheel. Installed the new blower wheel, hub clip, and here's the challenging task without the proper tool - putting the retaining ring back on the shaft! It took me about 5 minutes to put it back on the shaft with a small flat-head screw driver and an awl. Reinstalled the blower cover.

Next, I put the new belt over the pulleys and loosely hung the belt on the back tumbler to hold it up. Then I put the tumbler back in and worked the belt over the tumbler. I let the belt sat in the groove of the tumbler first and then when the tumbler was in position, I worked the belt over the two pulleys in to the proper position. Then I moved the belt to strap over the top of the tumbler. At this point, I just rolled the tumbler with my hand when part of the belt was out of the groove and on top of the tumbler. The motion took care of getting the rest of the belt out of the groove and on top of the tumbler as it should be located. Reinstalled the front tumbler and then the front panel.

Powered it back up and started the dryer and viola! the rumbling noise was not to be heard. Just like it used to sound - a low humming noise. Thanks Partselect.com for the helpful repair stories and the speed in getting the parts to me.

I was able to order exactly the same lint filter as the original. The dryer is a 1984 Maytag.Thank you Partselect.com

First I unplugged the dryer. Then, I took off the front cover, then a piece that holds the tumbler on. I put the new belt on and took a few minutes to make sure the belt was placed correctly. Lastly I put everything back on and plugged it back in. She started right up.

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always ... Read more replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.

The service from PartsSlect was outstanding.
Parts arrived next day and where OEM. I had the
dryer cleaned and operational in 1.5 Hr's
Keep up the great service.



Thank You

Remove the two screws that hold the front cover. Remove front cover and disconneted wiring to door switch.Remove the cover ( lower right hand corner )back of the dryer to gain access to belt idler pulley/tensioner. Remove old belt and slide new belt on the tumbler.