DDC4397VCL General Electric Dryer - Instructions

After taking the dryer apart and not finding anything that looks like the one I have in this box that I ordered, I got the right part and dryer is working find.

followed video direction ,pulled part ,compared to part on-line ,ordered part delivered in two buisness days and installed ,back in service .very simple and I will shop at your sight again and tell friends and family as well

sort of followed instructions, would have beenhelpfull if they told me I HAD TO REACH INTO THE MOUTH OF A SABRE TOOTHED TIGER to install the new belt.

The repair for the average untrained mechanicslly inclined " first off google directions/instruction picture step by step " we took off the wrong part which made this job difficult there is a part on the back that was removed prior to guided directions, called parts select they are awesome"our belt was delivered the next day on a 3 day weekend I was suprised second correct part sent anyone who took on this job , they will appreciatte all this . the belt was fairly easy to repair just do as directed follow guidelines. difficulty detaching a part that never should be"pain in the a" order your part from this company they rock" and picture guide and specific direction guideline @ this dryer has well outlived the money spent still kicking strong after several years of use hotpoint dryer

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.

I didn't know what was wrong at first, only that the dryer would not start. I bought it used so had no fear of taking it apart to diagnose. Found the broken belt inside, ordered a replacement, installed the new belt, then crossed my fingers. Was pleasantly surprised that was all that was wrong and that for less than $20, including shipping, a few hours of my time, and a little help from YouTube videos the dryer is working again!

I watched Youtube videos on how to troubleshoot the dryer but I did not go through all the testing of the fuses and the heat sensor. I did not want to take the dryer apart if I didn't have to. I turned on the dryer and looked into the bottom grate and saw no glow from the igniter (it should be very bright) so I started there. (The Youtube videos test the igniter last). Unplug the dryer. Turn off the gas. Pry off the grate. Unplug the igniter connector and set the multimeter to tone on continuity. There was no tone so it was bad. I used a flashlight that I put inside next to the gas valve to see. Remove the top flat cover on the burner assembly, 2 screws. (Had to do all this laying on my belly in front of the dryer. Very uncomfortable.) Remove the old igniter from the clamp. It fell apart as I took it out. Now the tricky part: The clamp is very tight and the igniter is delicate. I tried to slide it in from the top holding it between my index and middle finger and lining up the slots for the igniter 'wings'. I struggled with that until many-swear-words-later, I decided to slide the igniter in sideways. Put the 'wing' into the clamp's left side opening and then gently but firmly squeezed the 'barrel' into the clamp. It worked. Plug in igniter plug, put burner cover back on carefully without banging igniter, turn on gas, plug in dryer. Turn on dryer. Igniter should be very bright when it lights. It takes a little while to heat up the heat sensor that will open the gas valve and the burner should light.

Watched the video on YouTube and everything went great!

inserted the latch into the opening in the front face of the dryer

Removed two screws from front by door. Removed back panel to remove belt from tensioner. lifted lid of dryer. removed two more screws from inside to remove front panel. while holding the barrel I removed the front panel then grabbed barrel and pulled out. took off the old bearing, put the new one on and reassembled it the way I took it apart. The whole thing took about 10 min was quick and easy if there is any problems while you are doing it look it up on youtube.com and you can see it done.

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

Took off the top cover then took off the front panel and installed the new coils on gas valve.

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.