DB5710DT Samsung Dishwasher - Instructions

Took out rack, removed old wheels and got the new ones installed.

I called for a Lowes where I purchased the dishwasher was told it was out of warranty, they set up for a repairman to come out and fix it. He came out and told me it would be $190.00 for parts and labor but that didn't include the service call of $60.00 dollars. Total bill would be $250.00, plus it would be another 2 weeks before he would ... Read more be able to get back because he had to order the part but and get this I would get the part delivered to the house before the two weeks, and that he wouldn't guarantee the part for more then 90 days.
I told him no way, so I researched the internet and found this site part cost $25.00 dollars my time about 30 min. SAVINGS of $225.00.
The part was pretty easy to install had to take out a few screws around the edge. Only trouble I had was putting in the handle but I figure that out and put everything back together again.
I would purchase parts from this company again had it within 2 days, at a very reasonable cost.

It was very simple and easy. I opened the panel inside the door; total of 8-10 screews. The latch has two electrical connections and switches. The replacement part I got came with an extra set of switches. Replacing the switches needed an electrical tool which I don't have so I decided to keep the old ones. It is quite easy to take out th ... Read more e switches and replace the latch. I should have taken out the power; but I did not. I was just careful handling the wires et al; no big deal either. My dishwasher is working fine now. I was able to fix it within $40 and 1 hour of effort. Any technician would have cost me atleast couple of hundred bucks + parts etc.

After checking the door switch I found the micro switches were working but the unit would not start on the control panel. Thinking the latch was worn, I ordered a replacement. After changing the replacement latch and switches that came with it, the unit would still not start. I checked the switch and it is making contact. I can start the ... Read more unit after I close the door using the handle of a pair of pliers. So I assume the control board is bad, due to the fact that it will not initialize the control panel until the door is closed. Now I have ordered a control board and will replace...stay tuned!!

Finally had to remove front foot panel and laminated top. Removed screws on back and one side to get to open cabinet to insert hose properly.

Took the door of the dishwasher apart and the replaced the lever assembly. The lever assembly does not come with a door handle, so you have to remove the old door handle from the old lever assembly and install the door handle on the new lever assembly. Installing the handle on the lever assembly was the hardest part, the rest of the ins ... Read more tallation was easy.

All I did was put the new wheels on. They were really fast with shipping. I put my order in one day and the parts were there the next.

Pushed them on

This was the easiest repair I have ever done! Ordered in a few mins, and received the very next day. Opened the box and installed the two wheels - Done. That was Easy! Thank you so much for such quick service! Most definitely will use your company again in the future.

I'm so happy I ordered these wheels, with them it's running
like new. Without the wheels it was making grinding sounds when it ran. You just push them onto the rack spokes and snap them in place. EASY!

Replase door lach Thang you for the fast respons Peter Hansen

All screws are on the inside of the dishwasher.Not a good place when the washer is closed and the handle breaks.Had to take a box cutter and remove some plastic in the handle area to be able to remove broken handle and open dish washer.Once open this repair is a piece of cake.2 wires and a hand full of screws.

the removal of panel was simple, the removal of electrical connections was difficult even with a little wd 40 i was nervous when any metal part is attached to a plastic part. it didn't want to let go but my suggestion is to work the connecter back and forth forward and back to get it started then with a firm grip on the wire harness with ... Read more pliers pull the two apart with pliers. good luck!!!