CS24G6DW Crosley Refrigerator - Instructions

Followed the directions included with the parts, which were exact and well illustrated. If you are comfortable working around circuit boards and electrical connectors (with the power OFF, please!), then you can do this repair. Why electronics on this repair? Because you have to unplug a board to get to the parts, and disconnect the connectors to the solenoid. But again, the directions were fabulous, and I'm almost looking forward to needing to use PartSelect again. Almost.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

the entire assembly was removed using some small hex and torx wrenches. I am not a refrigeration expert and had no diagram but this was very intuitive to replace all the parts above. I figured I would replace all these other related parts while I was digging around in there.

One thing to watch out for is to label the wires going into the switches before you take the old one out. You do not want to wire them up wrong, so use a sharpie to label the colors before disassembly.

Also take the time to clean the parts in soap/bleach to clean all the years of filth that accumulate.

I replaced all the parts above and cleaned everything well in under 20 minutes. Saved a fortune thanks to partselect!

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

This is an easy repair. It took me longer to remove the bins off the inside of the door and clean then up, then the actual repair. Remove the top hinge trim 1 Phillips screw. After the hinge trim is removed you'll see 3 hex screws. Remove the 3 screws. Hold and open the door half way, and lift up on the door. The door is not heavy. Use your kitchen table as a work bench. Place the door flat on the kitchen table . On the bottom of the door you'll see the "CLOSER" One screw removes it. Reverse operations and reassemble. Note: Put a little Vaseline grease on the pivot point. Thats it ... 15 minutes and your done plus you saved a $65.00 service call.

Removed the rubber gasket and checked the switch. The switch displayed signs of scorching and the plastic was very brittle. Removed the switch which was held in by a small bracket and one screw. Replaced switch on bracket and remounted the switch. It took longer to reinstall the rubber gasket that to diagnoise and repair the switch. This was a very easy repair and the time from the part order to receiving it was two days. I'm very pleased with the part availability and quick shipping.

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

First I unplugged the refrigerator. Next item was the ice-maker; remove (3) screws and unplug it from the back wall. Third task is remove the (4) screws that attach the back wall of the freezer compartment. Lift the wall up enough to dislodge the center cooling shaft that the fan rides in and remove the rear wall. The last item is the fan motor which is attached to the freezer wall by (2) screws and (3) wires which are easily removed. Change out the motor and reassemble freezer compartment .

I went straight to PartsSelect on line and within minutes I found the appropriate brand of parts for my refrigerator. I simply removed the old trim shelf and snapped the replacements in place. I also inserted the glass shelf trim. No tools were required.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Our 20+ year old Maytag refrigerator suddenly started dispensing water one day without anyone near the refrigerator. Thankfully, my wife was nearby; my son temporarily solved the problem by shutting off water to the house. The ice dispenser unit has a "Lock" switch which turns off power to the ice & water dispenser. With the switch in the "lock" position, we were able to continue using the refrigerator (and turn the water back on) until I was able to get a replacement part.

The biggest hurdle that I encountered was removing the trim; I spent perhaps an hour and a half trying to figure it out. In the end it turned out to be easy and would have been perhaps half an hour job total had I known the trick. So... to remove the trim on a Maytag RSW2400, you remove a single Phillips head screw on the bottom of the trim. The trim then slides to the left and can be removed.

The next mistake I made was removing the entire dispenser unit. Instead, if you look closely, there are screws which may be used to disassemble part of it, leaving the ice/water dispenser housing mounted to the refrigerator door. This provides access to the ice/water actuator switch. Perform this disassembly and access to the switch becomes obvious.

The switch is held in place with a single Phillips screw. Make sure that you've disconnected the power to the fridge well before this point because, AFAICT, 120VAC flows through this switch! The switch that I replaced didn't appear to be in bad shape and, once removed, the switch seemed to work correctly when I tested it with an ohmmeter. I replaced it anyway.

Reassembly was straightforward and easy. Better still, ice and water are now dispensed correctly again.