CFW4700LW0 Crosley Washer - Instructions

With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.

For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!

First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.

Remove top of washer, remove door lock assembly,install new assembly replace top.

I removed the top panel of the washer, removed the soap dispenser to get to three screws. There were two more screws at the top of the control panel to remove, then removed the washer select knob, unclipped the panel box to remove the control box. Removed four more screws, then took a few parts off the old control panel to put on place on the new one, unclipped the wiring harness and installed the new panel. This control board has been replaced twice since I have owned this washer. My wife did the repairs herself.

love parts select have used them several times for parts great company

Very basic replacement- 2 screws in and out. The part did not come with screws to be sure to save them if you remove the broken part ahead of time to make the process smoother.

Did it with no problems at all just followed the video step by step worked great done in 1hour!

Remove screws take off striker .Put striker back on with screws back on

Tighten screws. Took 5 minutes

Removed the 4 screws holding the top on. Pulled top forward to release front catches and stood top up out of way. Removed 2 screws holding door lock. Could not unplug wire plugs from door lock because wires too tight. Removed 2 screws holding lower front panel and removed panel. Pulled door lock down and unplugged old lock and plugged in new lock. It was easier to position door lock to reinstall screws by working from top, so top removal wasn't a total waste of time. Reinstalled front panel and top. Machine works.

just unscrewed the old one and put a new one on.
I bought two just in case this one breaks too.

easy repair. I went to the back of the washer and removed the two(?) screws that held the top panel on. Then moved to the front of the washer and unscrewed the two screws in the door frame holding the lock assembly. Pulled it up and out from the top of the washer and disconnected the three wire connections. Then I just reversed the process with the new part. It all worked great. This website rocks...
Phil
Jax, FL

Very simple hardly worth writing about.

Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!

ordered the part and got the part in three day. A no hassle experience. Installed the latch and eureka! Fixed!