CDG4205AWW Crosley Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas flame shutting down after a minute.
-
Rommel from hercules, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drying had starting making a loud screeching noise
The noise started intermittent and got worse. After watching an online repair of a very similar model and same brand, I decided to tackle it myself. The problem was that one of the drum support rollers had seized up. The shaft that support roller road on was also a little sticky. The noise was caused by the roller hitting the sheet metal behind the drum support roller and scraping on it. I replaced the shaft and drum roller and believe that solved the problem. I ordered other parts for the dryer drum assembly and replaced them while I had it apart. I didn't want to take it apart twice so I didn't take the time to disassemble to diagnose it. I just ordered them all and replaced them all while I was in there.
Parts Used:
-
Bill from Bend, OR
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Our dryer would not ignite, so I figured it was the radiant flame sensor. Well, I out that in and still nothing. I found out that the Tube Burner was also burned off on the flame end, by the igniter. I also ordered that part. installed it, and it works beautifully.
On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.
Parts Used:
-
Rodney from Zimmerman, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Flame when out to fast. Dryer did not get hot enough.
Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.
Parts Used:
-
Neil from Harwich, MA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Torn lint filter
-
E from San Francisco, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
It was making a lot of noises
IT was good My husband fixed it .sorry we didn't take video but it is working alright. Thank you
Parts Used:
-
Margaret from Bedford, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!