Models > CDB900NB3A > Instructions

CDB900NB3A Crosley Dishwasher - Instructions

All Instructions for the CDB900NB3A
106 - 120 of 432
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bottom seal on door came out and melted on heating element.
Took me about 2 minutes to repair, no tools to repair, very easy installation repair!
Parts Used:
Dishwasher Door Bottom Seal
  • Danny from Collierville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water did not drain. Found the door latch broken
Unplug dishwasher. Open the door. Remove two Phillips head screws holding the door panel on. Slide door panel down and out to remove. With door still open, remove the six T20 torque screws that hold the control panel. Behind the control is the latch assembly. Take a picture of the wires going into the latch assembly for installation reference(mine was black wires on left and white wires on right). Unplug the two sets of wires. Remove two T20 torque screws that hold the latch. Replace with new latch and reverse steps for installation.
Parts Used:
Latch
  • Casey from Keota, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the end on one of the door springs on the dishwasher broke off
I removed the access panel using a nut driver. One fastener on each side at the lower front panel. Move the two piece lower panel and set aside. Locate the broken spring. It will be on the floor under the dish washer. Remove the broken spring. Place the new spring end in the hole in the chord end and place the chord over the plastic guide. Use a pliers to stretch the spring and fasten it to the hole in the lower dishwasher frame at the back of the dishwasher. Check the door for proper tension. Replace the lower panel and secure with the two screws. I recommend replacing both springs at the same time to insure proper balance. If you only replace one spring you will be replacing the other in the near future.
Parts Used:
Door Spring
  • John from SUNBURY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old sprayer arm melted to heating coil.
Easiest repair EVER!!! You just pull the old spray arm off (be sure to keep all the smaller pieces that click it into the bottom of dishwasher) and pop the new one in. Done!
Parts Used:
Lower Spray Arm
  • Rhiannon from FEDERAL WAY, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower swivel arm broken
Unsnap old and snap on new
Parts Used:
Lower Spray Arm
  • John from DOTHAN, AL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Faulty pump
Replacement was every bit as simple as the website said it would be.
Parts Used:
Pump Motor Kit
  • Rick from SHICKSHINNY, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
several issues with dishwasher
Easy fix but not cheap
replaced drain trap and four rack wheels with clips

All parts were expensive for the items.
found cheaper wheels w/clips for much less on another site.
Parts Used:
Drain Trap
  • Nicholas from KESWICK, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old basket developed holes and needed replacing.
Took the old out and placed the new in its place. That simple!
Parts Used:
Silverware Basket
  • Gilbert C from COTTONWOOD, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Leaking from Bottom of Door
Replacing the part was easy. Just pop the old one out and pop the new one in. This item fixed my leaking door problem. The old arm had fallen against the heating element, which burned a hole through the end. Water was shooting out that hole and leaking under the bottom door seal. Replacing the door seal did not help, but replacing the arm fixed the leak.
Parts Used:
Lower Spray Arm
  • Loren from Sacramento, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking Dishwasher
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Parts Used:
Dishwasher Tub Gasket - Gray
  • Andre from La Mirada, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dish washer leaking at the door
Pulled off the old gasket and replaced it the same way with the new one.
Parts Used:
Dishwasher Tub Gasket - Gray
  • Brian from Milford, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cutlery basket
Simply took the old one out, and put the new one in.
Parts Used:
Silverware Basket
  • Mena from Sarasota, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic piece that held the arm on was worn & dishwasher only 2 yrs old.
Arm screwed on and immediately fixed the problem.
Parts Used:
Upper Spray Arm
  • elner from new concord, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower sprayer arm melted after being lodged
Pulled the old one off and pressed the new one on (plastic clips hold it on). Dishes much cleaner now.
Parts Used:
Lower Spray Arm
  • james from PENTWATER, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing grommet
Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.
Parts Used:
Water Delivery Tube Grommet
  • Jack from KENDALLVILLE, IN
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CDB900NB3A
106 - 120 of 432