CDB900NB3A Crosley Dishwasher - Instructions

Removed all sealer and install new one as instructed.

Removed screws for door panel, then literally 2 screws to change out the latch!!

Disconnected power, water, and drain tube from dishwasher. Pulled dishwasher out and laid it on right side. It was not necessary to remove the pump motor. When disconnecting the water line, it is better to remove 3/8 line from the appliance adapter rather that the appliance adapter from the dishwasher as the nylon connection tends to strip.

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Replace the latch. Got to cut off old latch, trim wires, install latch, and put on the dishwasher door cover back on with screws

Pump motor kit changing the pump went good little tough to get the old one out And the new one went in a little tough really had to push hard to get it in but it works great took longer to take out the dishwasher and put it back in instead of changing the actual part

I left the unit in place. I removed the bottom cover, unplugged power from GFI receptacle and closed water supply valve. I unplugged the electrical connection. I put a dishtowel under water inlet valve and removed water supply. I removed two screws from inlet valve bracket that allowed me to rotate the valve and used pliers to remove water hose clamp and hose. I installed the new valve in reverse order. I checked for leaks; found none. Life is good again!

Although the part I ordered was not an exact match, it was a Frigidaire piece and fit onto the spray arm assembley the same way. And if I do say so, it actually seems to clean the dishes better! All I did was clip the new one into place.

i just took off the old and poped on the new, it was way to easy! no tools required!

Easy

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!

Unscrewed the housing for the old piece and screwed on the new part. No tools needed. Easy to use website, fast delivery. Very easy.

I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.