CDB500CGS3 Crosley Dishwasher - Instructions

I rolled out the old bottom dish rack and rolled in the new one with no problems. In fact, the new bottom dish rack is much better that the original that came from the factory. It only took about less than one minute.

I watched the partselectrepair videos for tub gasket, bottom gasket, and splash shield. The instructions were very clear and easy to follow, thank you so much now I have a dishwasher that's good as new.

Grab the tab on the support and rotate 1/4 turn counter-clockwise to unlock it, then lift it off. The lower spray arm simply pops off the support by spreading two tabs underneath.

Align the opening in the lower spray arm support with the outlet post in the bottom and rotate 1/4 turn clockwise to lock.

*Note: direction to remove the filter basket differed from the manual. Visually line up the notches and do not twist too far when locking or you WILL break the retainer tabs.

Simply center the lower spray arm over the support and press down until it locks into place.

Pulled out old gasket and shield guards and put in new ones. No tools needed. Piece of cake??

I JUST FOLLOWED THE INSTRUCTIONS . PIECE OF CAKE

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

Our dishwasher sat in a warehouse for a year after our move from CA to TX. When I finally installed it, there was some sort of white mineral deposit that had built up on the heater element. I didn't notice it back in CA. I tried to get as much as possible off but it kept building. So I purchased a new heater element. It's been in for a few weeks and my wife thinks the build up is happening again.
To Repair;
Unscrew the dishwasher from the counter. They'll be one or two screws attaching the dishwasher on the underside of the counter.
Pull the washer out carefully.
Remove any dishes and the bottom rack.
Tilt washer on it's side.
Remove wire connections to heater element (They slide right off but make sure to remember which one goes where)
Unscrew the nuts that are holding the element on. I used some pliers. It wasn't difficult.
Remove old element and replace with new.
Reverse order.

Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks

Removed the 4 screws that held the dishwasher in place, tilted it out, removed 2 nut screws on striker, installed new striker and put it back together. Very simple.

Thank you for stocking the parts and shipping them as promised.

I'm a stay-at-home mom of 3 kids, so I enlisted the help of my oldest son (5 years old) for this job while the 2 little ones were asleep! First we cut the power to the dishwasher, then we removed the 2 bottom screws on the stainless steel front and slid it off to expose the back of the dispenser. We removed the red and white wires from the left side of the dispenser, took out the 6 screws holding the dispenser in place, put in the new dispenser, hooked up the red and white wires (in the right order), and flipped the breaker back on! We ran a cycle to make sure it worked, and it did!! My husband was thrilled! He thought for sure we needed a new dishwasher! :o) Thank you, PartSelect!

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks

I already had the dishwasher pulled out (remove the two screws from under the counter holding the dishwasher in place) The drain was located on the right side at the bottom very easily removed after taking out the two screws and removing the tubing. Attached the tubing to the new drain pump, made sure clamps were in place and then screwed the screws back in to hold the drain pump into the bracket. Ran the dishwasher once before pushing it back in to make sure there were no leaks. Had a leak but completely unrelated to the drain pump.....I had to replace the hot water supply line the next day, also SUPER EASY. Pushed dishwasher back in and replaced the two screws into the brackets that hold the dishwasher in. Kind of disappointed that I had to replace these things since the dishwasher is just over a year old, but PartSelect made finding the part super easy and they were by far the BEST PRICE! Thanks again! Only suggestion is I wish that it would have come with directions...but I figured it out pretty well!

Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.

I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).