AS829CSBGB Maytag Refrigerator - Instructions

I followed the video of your repair man. Made it very easy.Thanks.

It was only the door but it wouldn't come out without disassembly of the entire dispensing section; this meant removing the front section and disconnecting 2 pcs from 3 wire harnesses...much more involved than I thought. The spring and strike were fine, but when I reassembled the unit it didn't work. The key was the mechanical connection ... Read more with the solenoid. It is not obvious and directions would have been helpful. BTW unlike me, flip the power off. I got a good shock from the accuator.

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man ... Read more showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove ... Read more , 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.

Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good ... Read more enough.

I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, i ... Read more t is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.

Removed old ejector arm and installed new part.

Remove upper hinge with socket set. I found it helpful to remove the door spring (on bottom of door) in order to be able to lift out the door from lower hinge. Replace bushing. Replace door, upper hinge, you're done. I did note that lower hinge post (~10mm OD) had worn against the frame due to the loss of bushing, losing ~1-2mm of met ... Read more al. Would not have seen this until the door was off. Was concerned this will lead to premature failure of the new bushing, but it will be a much harder job to replace lower hinge (looks like I will need to empty and tip the fridge to access lower side), plus I didn't have the lower hinge part handy (~$40-45), so I will replace both if the bushing fails again.

Followed included instructions. Thank you.

Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.

looked a website removed part found broken item order and installed in 15 minutes, easy simple fix very low cost change

rl

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

piece of cake . removed the cover - one screw in the switch and back together again - maybe 10 minutes.

Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.